Activity
 
Notifications
Clear all
madane
@madane
Active Member
Joined: Jan 3, 2008
Topics: 0 / Replies: 15
Reply
RE: A DMX controller for multiple RGB pixel strings

I hope this is a very interesting RGB pixel project . I will start working for it thanks for the information

14 years ago
Forum
DMX
Reply
RE: Ren48LSDv3c pic programing problems?????

Hi Mr Dirknerkle thank you for the reply i have printed nearly 350 pages from Doit yourself site and i had been working for this project from past si...

14 years ago
Forum
Reply
RE: Ren48LSDv3c pic programing problems?????

Hi The signal i meant to say is the wave form in the oscilloscope,The renard control is being tested directly through RS485 interface from the PC, i...

14 years ago
Forum
Reply
RE: Ren48LSDv3c pic programing problems?????

Hi everybody, Thanks a lot with the information given i was able to solve my problem. I was messing the firmware configuration with the harware. Than...

14 years ago
Forum
Reply
RE: Ren48LSDv3c pic programing problems?????

Hi everbody, Thanks everyone for the infomation. Ok i start from the scratch my idea is to use renard controller to controle 5 parallel led lights a...

14 years ago
Forum
Reply
RE: Ren48LSDv3c pic programing problems?????

Hi everbody, Thanks everyone for the infomation. Ok i start from the scratch my idea is to use renard controller to controle 5 parallel led lights a...

14 years ago
Forum
Reply
RE: Ren48LSDv3c pic programing problems?????

Hi , There is no one to help me for the past 6 day i am workingwith renard48LSD i have no solution no one to help me !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!...

14 years ago
Forum
Reply
RE: Ren48LSDv3c pic programing problems?????

Hi , There is no one to help me for the past 6 day i am workingwith renard48LSD i have no solution no one to help me !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!...

14 years ago
Forum
Reply
RE: Ren48LSDv3c pic programing problems?????

Hi to all , I have just now assembled Renard48LSD with ULN2803 for the moment i am using only one PIC16F688 programmed for test drive i am not able t...

14 years ago
Forum
Reply
RE: XBee Wireless Modules

Hi , Renard wireless connected with RS 485 data to Renard wireless and i am able to communicate with the other wireless after changing the configira...

14 years ago
Forum
Reply
RE: XBee Wireless Modules

HI Dirknerkle I have Purchased Hexin 485 converter as per the data sheet DB9 pin 1 = -Data Pin 2 = +Data so i have to connect -data to 1&2 of J1 i...

14 years ago
Forum
Reply
RE: XBee Wireless Modules

Hi Xenia Thanks for the reply i have not yet assembled the controller board to test with the renard WC receiver Madane

14 years ago
Forum
Reply
RE: XBee Wireless Modules

Thanks Dirknerkle, Today all shops are closed i will buy the converter and make a test and keep you informed on monday. Thanking you once again for...

14 years ago
Forum
Reply
RE: XBee Wireless Modules

Hi Dirknerkle, Thanks for the reply. I changed both Xbees 57600, 8 bits, NO parity and 1 stop but still i am not able to hook it up. My installation i...

14 years ago
Forum
Reply
RE: XBee Wireless Modules

Hi i have buit two wireless renad one with emode and other as TX . i have connected the emode unit to serial port of PC with RS232 patch with two RJ45...

14 years ago
Forum
Share: