XBee Wireless Modul...
 
Notifications
Clear all

XBee Wireless Modules

19 Posts
7 Users
0 Reactions
9,207 Views
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago
omzig wrote:FYI, SparkFun has the 2mm sockets as well as a lot of other XBee stuff. When I was doing a little experimenting with them I used these with a standard breadboard.

These are exactly what we used for the Helix systems which use the XBee Pro modules. Yeah - and what is with that 2mm socket?!


Reply
dirknerkle
Posts: 10308
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

RE: 2mm female header sockets

Thanks, budude and omzig. I have ordered them from SparkFun in the past and have more coming from them -- I'm sure they're also available through Mouser because it would be so much more convenient for everyone to get all the stuff from one place in a BOM. I just haven't found the part number yet...

EDIT - 9/9/09: Mouser has more than a thousand of these on order as part # M22-7131042. They are RIDICULOUSLY EXPENSIVE for such a tiny part. To mount an XBee module, you'd need a pair of them. I'll try to find a suitable workaround but right now, at $1 each, SparkFun has Mouser's price beat hands-down...

EDIT - 9/10/09: If you search eBay for the word "xbee" you can find good deals on breakout boards, programming boards, and interface boards for USB and otherwise. Watch out for the shipping prices though...

EDIT - 10/12/09: Mouser finally has these in stock, but you'll have to buy 50 of them to get the price down to $1.02 each. (I told you they were ridiculously expensive!)

EDIT - 9/14/09: started new thread for "Renard-WC"


Reply
Posts: 15
(@madane)
Active Member
Joined: 19 years ago

Hi i have buit two wireless renad one with emode and other as TX . i have connected the emode unit to serial port of PC with RS232 patch with two RJ45 and JP5 Jumpered. I have connected Xbee with USB explorer and connected to other pc.The Parameters for both Xbee module as follows 576OO Baud -Pan ID 3332 - MacMode 802.15.4 No ACKS - Parity Mark parity -PackTimeout 0. I use XCTU terminal to communicate but there is no communication between the module. I only see the TX led from the explore blinking when a data is sent . I tried with vixen also no response.

Please kindly help me for the same
Madane


Reply
dirknerkle
Posts: 10308
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
madane wrote:Hi i have buit two wireless renad one with emode and other as TX . i have connected the emode unit to serial port of PC with RS232 patch with two RJ45 and JP5 Jumpered. I have connected Xbee with USB explorer and connected to other pc.The Parameters for both Xbee module as follows 576OO Baud -Pan ID 3332 - MacMode 802.15.4 No ACKS - Parity Mark parity -PackTimeout 0. I use XCTU terminal to communicate but there is no communication between the module. I only see the TX led from the explore blinking when a data is sent . I tried with vixen also no response.

Please kindly help me for the same
Madane

When you're daisychaining one Renard to another, you need to use 57600, 8 bits, NO parity and 1 stop for the XBees. This is because the Renard firmware does not generate a parity bit. The MARK parity only applies to communication between an XBee at the computer and the first Renard controller. Change the Xbees to use no parity and I'll bet they'll hook up fine. BTW, remember than in eMode, the Xbee radio is on the TX side of the Ren-W and JP5 is connected.


Reply
Posts: 15
(@madane)
Active Member
Joined: 19 years ago

Hi Dirknerkle,
Thanks for the reply. I changed both Xbees 57600, 8 bits, NO parity and 1 stop but still i am not able to hook it up.
My installation is like this . I send the sequence of VIXEN to serial port where the Renard-WC connected, to Transmit the RF signal, and i use another Renard-WC to receive the sequence to the Renard controller.

I also hooked the xbee unit to two pc one direct with Renard_WC and other with Xbee explorer using the XCTU.No communication with the Xbee module.
Thanking you in advance
Madane


Reply
Page 2 / 4
Share: