XBee Wireless Modul...
 
Notifications
Clear all

XBee Wireless Modules

19 Posts
7 Users
0 Reactions
9,208 Views
dirknerkle
Posts: 10308
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
[#7823]

I thought I'd start this thread by sharing the prototyping PCB layouts I'm using to develop a generic wireless add-on solution for DIYC controllers. While the project test base will be made with Renard SS24 units, the eventual goal will be to make the concept easily transportable to other controller types as well.

I have placed the basic set of prototyping board layouts in the COPPER section of the File Library. The boards are certainly excellent candidates for home-etching. Enjoy!

Here's a sample of what the "Spyder" board looks like:


18 Replies
dirknerkle
Posts: 10308
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

Progress report...

I have a working setup that is pretty kludgy at the present time, but the concept seems to work. More Xbee modules are on the way for more testing, as well as a single 2-3/4" square circuitboard that can simply plugged into J1 and J2 on the Renard board, with a tap off the +5v of the Renard's power circuitry (my current thought is to use the 5v test hole).

Parts for a completed board include a MAX232 chip, three capacitors, a 3.3v voltage regulator, a couple RJ45 jacks and a couple XBee modules...

More later, but things are looking up for a pretty simple, near plug-n-play wireless add-on transmit/receive adapter for under $50... or under $30 if it's a receive-only adapter.


Reply
Matt_Edwards
Posts: 2664
(@matt-edwards)
Famed Member
Joined: 18 years ago

Great concept.

  • What speed will is run at? (sorry I know I should look up the spec, but today I am lazy)
  • Will it be protocol dependant, or are you attempting to make a wireless piece of string.

Your picture is very small. have you got a bigger one 1/2 blind folks like me can see?

Cheers
Matthew


Reply
dirknerkle
Posts: 10308
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
Matt_Edwards wrote:Great concept.

  • What speed will is run at? (sorry I know I should look up the spec, but today I am lazy)
  • Will it be protocol dependant, or are you attempting to make a wireless piece of string.

Your picture is very small. have you got a bigger one 1/2 blind folks like me can see?

Cheers
Matthew

Thanks for the interest!

My goal is to make it as generic and as configuration-free as I can -- even to the point of attaching it to a Renard board. Right now it just plugs into the Renard's RJ45s, and I'm experimenting with ways to get the 5v power from the Renard -- I'll probably use the left side of JP3 by soldering a wire to a jumper shunt and that way, you can either close JP3 or connect it only to the left side of JP3 to get the power.

In keeping with the "generic" concept, my testing is at 57.6K -- the basic Renard speed. I've tried it at 115 and it works fine there, too. When configuring one of the XBee modules, there are only 2 things to set: the PAN id and the transmission rate. Alternately, instead of using the PAN id, you could set each module's address manually, but more on that at a later date...

It uses the default XBee protocols right out of the box. No changes. I've figured out a mechanism to daisy-chain multiple Renards this way as so far, the control signals have been passed along properly from one Renard to the next.

Sorry about the pic -- the prototyping boards I made for this project are in the File Library under COPPER, and there's a larger picture of the "spyder" board there -- the same one as this small photo. (I'll see if I can fix the photo problem!)

Right now I'm waiting on a few parts so I can continue testing. The XBee modules plug into a wierd 2mm female header, which doesn't conform to almost anything. I haven't found the right part from Mouser yet, but I'm sure that'll be part of the BOM once I'm satisfied with this thing. So far I'm really pleased with it, but all too often we discover that stuff that works on the bench or across the room croaks when it gets outside. It'll be interesting to see what effect the broadband-type protective boxes most of us use have on transmission distance when that little 1" antenna is locked away inside...


Reply
omzig
Posts: 1603
(@omzig)
Noble Member
Joined: 19 years ago

FYI, SparkFun has the 2mm sockets as well as a lot of other XBee stuff. When I was doing a little experimenting with them I used these with a standard breadboard.


Reply
Page 1 / 4
Share: