XBee Wireless Modul...
 
Notifications
Clear all

XBee Wireless Modules

19 Posts
7 Users
0 Reactions
9,208 Views
gdyrdave
Posts: 916
(@gdyrdave)
Noble Member
Joined: 16 years ago

Hey Dave,
I have XBEE modules out the kazoo!!! Want me to help?

The other Dave

PS: I am NOT one of the DIGWDF engineers..... Not fond of lutefish....lol


Reply
gdyrdave
Posts: 916
(@gdyrdave)
Noble Member
Joined: 16 years ago

Also if you need connectors for the XBees i have some I got from china... Need some?

the other Dave


Reply
dirknerkle
Posts: 10308
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
madane wrote:Hi Dirknerkle,
Thanks for the reply. I changed both Xbees 57600, 8 bits, NO parity and 1 stop but still i am not able to hook it up.
My installation is like this . I send the sequence of VIXEN to serial port where the Renard-WC connected, to Transmit the RF signal, and i use another Renard-WC to receive the sequence to the Renard controller.

I also hooked the xbee unit to two pc one direct with Renard_WC and other with Xbee explorer using the XCTU.No communication with the Xbee module.
Thanking you in advance
Madane

Okay, if I understand your setup, it's like this:

The vixen Renard plugin is set to 57600baud, 8 bits, no parity 1 stop bit. and it's set to go out the PC's serial port.
The serial port is connected to the Ren-W to transmit.
The controller has a Ren-W to receive.

For this to work, you need the following:
1. The serial connection from the computer to the Ren-W must be RS485. RS232 is not going to work. You need an RS232 to RS485 converter and you need to set the cable connections from the RS485 converter correctly so it connects to the Ren-W using the standard, Renard cabling setup for RS485.

2. The Ren-W at the computer must be in TX mode. The XBee in that Ren-W can be at 57600, N, 8 1 or it can be at 57600, M, 8, 2. Whichever setting you use, the Vixen Renard plugin setting must be set the same way. If the transmitting Ren-W is a Rev6 board, you need the jumper settings on the TX header pins and nothing on the RX pins. If it's an SMA version of the Ren-W, you need the XBee radio in the TX side of the board, and the cable from the computer in the LEFT side of the board, and the JP5 jumper OFF because it is not an e-mode repeater.

3. The Ren-W at the receiver controller must be in RX mode. The XBee in that Ren-W must be at the same setting as the transmitting Ren-W. If it's a Rev-6 Ren-W, the jumpers must be on the RX pins and nothing on the TX. If it's an SMA Ren-W then the XBee must be in the RX side of the board and the data cable going from the RIGHT side into the controllers RS input.


Reply
dirknerkle
Posts: 10308
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
gdyrdave wrote:Hey Dave,
I have XBEE modules out the kazoo!!! Want me to help?

The other Dave

PS: I am NOT one of the DIGWDF engineers..... Not fond of lutefish....lol

You have them out the kazoo? Is that painful? :omg:

(BTW, the DIGWDF engineers aren't fond of lutefisk either... they often use it to replace the soles on their sandals... when they're not barefoot...)


Reply
Posts: 15
(@madane)
Active Member
Joined: 19 years ago

Thanks Dirknerkle,

Today all shops are closed i will buy the converter and make a test and keep you informed on monday.

Thanking you once again for the information.
Madane


Reply
Page 3 / 4
Share: