Hi everbody,
Thanks everyone for the infomation. Ok i start from the scratch my idea is to use renard controller to controle 5 parallel led lights as 1channel and i am going to control 24 channels of these strips with their own sequence programmed in vixen. My hardware setup is going to be like this. Vixen sequence from the PC is being transmitted using RENARD-Wireless . The Renard Wireless receiver signal is hooked to the Renard controller to control the 24 channels of 5 parallel leds. The remote Renard controller and wireless use battery power for +5 volt.I have even tried with 2N2222A transistor there is no output. Just for your information
i have checked the input of PIC 16F688 pin 5 i have the signal but i do not have the data output signal at pin6 of PIC . Sorry no complain just anxious to finish the project which i am trying to do from past one and half month. i was able to finish the wireless problem because of you all.Thanks for all of you once again and i hope i will also finish the controller.
I have already a board with ULN2803 connected with leds so i have connected the input of ULN2803 to the Output of PIC16F688 in series with 470R resistance ,I have also tried with 2N2222A only as a test drive. Just a question Zero crossing plays a main role for the PIC , Because i use a battery as power supply for the Renard Wireless and controller.PIC programmed with firmware Ren48LSD and changed the config #define PWM_build 1 – #define DC_build 1 – #define CTR_LOCKOUT 1 – ;#define OUTPUT_NEGATIVE_TRUE –
Thanking you in advance
Madane
There is no ZC on the Ren48LSD at all so you don't have to worry about that. It sounds like you have the Renard code changes correct although I suggest you stick with the compiled File Library versions (.hex files) as those are known to work.
1 - When you say you have a signal on pin 5 - what exactly do you mean?
2 - How is the addressing for the wireless boards set up?
3 - Can you test this without the wireless?
Hi everybody,
Thanks a lot with the information given i was able to solve my problem. I was messing the firmware configuration with the harware. Thanks for the effort my last question ? what i have to change if i want to use ULN2803 instead of 2N2222A, Because i have nearly 25 assembled board with ULN2803 and 5 parallel leds for each output which i was using before with OLSEN595
Thanking you in advance
Madane
Are the ULN2803's configured to sink the current from the LEDs? If so, they can directly replace the existing 2N2222 transistors (which fits with your descriptions above now). I don't know how far you assembled the LSD board at this point so the directions will differ a bit. If you have already built the board completely (with 470R resistors and the transistors), you can connect the RJ45s directly to the ULN2803 inputs since they are sinking outputs (for common anode LEDs). Please describe the state of the Ren48 as well as the configuration of the ULN2803 chips on your other board for the best answers.
Hi
The signal i meant to say is the wave form in the oscilloscope,The renard control is being tested directly through RS485 interface from the PC, i have not yet tested the control with the wireless but the connection will be like this ,From the PC to RS485 interface and the data A- to pin 4 of J1 Renard-Wireless and B+ to pin 5 of J1 Renard-Wireless and from Renard wireless Receiver to the control board. The Xbee configuration is PanID 3332 - Baudrate 57600- Parity NONE - API enabled and XB24 version 10E6 Fontion set i do not know what to set . Please keep me informed the correct setting for the Xbee. i will be back home within another one hour and i will test with the Wireless.My ULN2803 output pin 10 to 17 to each cathode of leds and common anode +5 volt. I have almost solved my problem except the wireless communication with the control.
Thanking you without your help i should not have come till hear
Madane
