Ren48LSDv3c pic pro...
 
Notifications
Clear all

Ren48LSDv3c pic programing problems?????

17 Posts
4 Users
0 Reactions
6,474 Views
Posts: 15
(@madane)
Active Member
Joined: 19 years ago

Hi ,
There is no one to help me for the past 6 day i am workingwith renard48LSD i have no solution no one to help me !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Madane


Reply
Posts: 15
(@madane)
Active Member
Joined: 19 years ago

Hi ,
There is no one to help me for the past 6 day i am workingwith renard48LSD i have no solution no one to help me !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
I have assembled Renard48LSD with ULN2803 for the moment i am using only one PIC16F688 programmed for test drive i am not able to get any output to the ULN2803 connecting a led with resistor on the output pin of PIC16f688 the led light stable . input pin 5 signal ok, Pin 4 signal ok with 10k, power supply ok 5volt pin1 and 14, pin 3,7,8,9,10,11,12,13 with reference with +5 gives 5volt when an led is connected it lights stable and output of ULN2803 nothing osc ok. Please kindly give infomation for this
Thanking you in advance

Madane


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

OK - so - I don't quite understand the purpose of the ULN2803 or how (or why) it's connected to the Ren48LSD. The Ren48LSD transistors outputs are much better drivers than a ULN2803 - and overall 8 general purpose 2n2222 type resistors are probably cheaper than a ULN2803. Can you explain how you have this connected?

I'm not quite clear on the symptoms? What are you using to run data to the Ren48LSD - Vixen? How is it configured, etc. Please explain the entire setup if you can.


Reply
dirknerkle
Posts: 10308
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
madane wrote:Hi ,
There is no one to help me for the past 6 day i am workingwith renard48LSD i have no solution no one to help me !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
I have assembled Renard48LSD with ULN2803 for the moment i am using only one PIC16F688 programmed for test drive i am not able to get any output to the ULN2803 connecting a led with resistor on the output pin of PIC16f688 the led light stable . input pin 5 signal ok, Pin 4 signal ok with 10k, power supply ok 5volt pin1 and 14, pin 3,7,8,9,10,11,12,13 with reference with +5 gives 5volt when an led is connected it lights stable and output of ULN2803 nothing osc ok. Please kindly give infomation for this
Thanking you in advance

Madane

If you're using the normal LSD firmware, the outputs are reversed on the PIC. This is by design because the LSD's transistors invert the polarity of the voltage again, sending the normal (expected) values to the RJ45 jacks. If you are only using one PIC16F688 in the LSD board, you'll need to make sure it's in the right position (for channels 1-8) or you won't get any signal to it at all. I'm also a bit confused why you need the ULN2803 with the LSD board. You might do well to explain what you're trying to accomplish instead of complaining that nobody has tried to help you, because so far, your description of what you're trying to do is not very clear.

EDIT: Mr. 48LSD beat me to it... 😆


Reply
Posts: 15
(@madane)
Active Member
Joined: 19 years ago

Hi everbody,
Thanks everyone for the infomation. Ok i start from the scratch my idea is to use renard controller to controle 5 parallel led lights as 1channel and i am going to control 24 channels of these strips with their own sequence programmed in vixen. My hardware setup is going to be like this. Vixen sequence from the PC is being transmitted using RENARD-Wireless . The Renard Wireless receiver signal is hooked to the Renard controller to control the 24 channels of 5 parallel leds. The remote Renard controller and wireless use battery power for +5 volt.I have even tried with 2N2222A transistor there is no output. Just for your information
i have checked the input of PIC 16F688 pin 5 i have the signal but i do not have the data output signal at pin6 of PIC . Sorry no complain just anxious to finish the project which i am trying to do from past one and half month. i was able to finish the wireless problem because of you all.Thanks for all of you once again and i hope i will also finish the controller.


Reply
Page 2 / 4
Share: