ESPixelStick - E1.3...
 
Notifications
Clear all

ESPixelStick - E1.31 WiFi Pixel Controller

948 Posts
178 Users
0 Reactions
503.8 K Views
Posts: 2048
(@scootchu)
Noble Member
Joined: 17 years ago

I would love to be able to control my esp8266 with my echo. I have some 2811 strips that would work great under my porch railings.


Reply
Barnabybear
Posts: 1583
(@barnabybear)
Noble Member
Joined: 15 years ago
scootchu wrote:I would love to be able to control my esp8266 with my echo. I have some 2811 strips that would work great under my porch railings.

Hi, it should be quite easy to do - see if you can find some infomation on the echo and I'll have a look at it. I'm a bit bogged down in another project to be doing much research.


Reply
Posts: 2048
(@scootchu)
Noble Member
Joined: 17 years ago

I am poking around and have found that the 8266 can emulate a wemo device, but I am not sure how to integrate the code to control 2811 pixels.


Reply
Barnabybear
Posts: 1583
(@barnabybear)
Noble Member
Joined: 15 years ago
scootchu wrote:I am poking around and have found that the 8266 can emulate a wemo device, but I am not sure how to integrate the code to control 2811 pixels.

I'd start a new thread.


Reply
Posts: 94
(@davros)
Estimable Member
Joined: 13 years ago

Is the artwork that is up on OSHPARK current? any errata? :pinch:


Reply
Posts: 173
(@smerk)
Estimable Member
Joined: 10 years ago

I am in need of help. I am finally getting around to programming these. The flash tool did not report any errors, but the serial output at the end is this:

Connecting to LIGH�5!OUHC��e,W�� W�� jA.........C��n��tY��tJA:�9&)�8 r1�
�-��i��t��r�5Mj
K��b��rW� .W�tYz� �r�0C� b�sW�i��fK�5Lc+�nYk� ��m��iW�sY� ��
�


Reply
Posts: 1344
(@mrsmoofy)
Noble Member
Joined: 12 years ago
Smerk wrote:I am in need of help. I am finally getting around to programming these. The flash tool did not report any errors, but the serial output at the end is this:

Connecting to LIGH�5!OUHC��e,W�� W�� jA.........C��n��tY��tJA:�9&)�8 r1�
�-��i��t��r�5Mj
K��b��rW� .W�tYz� �r�0C� b�sW�i��fK�5Lc+�nYk� ��m��iW�sY� ��
�

I think most people had this problem as well as myself. No need for alarm yet. If you configured it to connect to your wireless network you should be able to go into your router to see what IP address your router gave to it and then you can browse to that IP address.


Reply
Wildbill
Posts: 259
(@wildbill)
Reputable Member
Joined: 16 years ago
Smerk wrote:I am in need of help. I am finally getting around to programming these. The flash tool did not report any errors, but the serial output at the end is this:

Connecting to LIGH�5!OUHC��e,W�� W�� jA.........C��n��tY��tJA:�9&)�8r1�
�-��i��t��r�5Mj
K��b��rW� .W�tYz� �r�0C�b�sW�i��fK�5Lc+�nYk� ��m��iW�sY� ��
�

Happens to a lot of people. It's the result of a cheap programmer but if you get a program called putty you get around it and find the IP address

Sent from my iPhone using Tapatalk


Reply
Wildbill
Posts: 259
(@wildbill)
Reputable Member
Joined: 16 years ago

The problem is the baud rates are conflicting in the answer It gets from the programmer

Sent from my iPhone using Tapatalk


Reply
Kev7274
Posts: 2037
(@kev7274)
Famed Member
Joined: 13 years ago

Depending on how fast you need it,I got this one and it works CORRECTLY and having the aluminum case helps keep from damaging anything. Got it in 10 days.
http://www.ebay.com/itm/201541559252?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT

Or you can just use Putty as mentioned.


Reply
Page 54 / 95
Share: