MegaPixeltree setup...
 
Notifications
Clear all

MegaPixeltree setup problems

5 Posts
3 Users
0 Reactions
56 Views
Mudsculpter
Posts: 1222
Admin
Topic starter
(@mudsculpter)
Member
Joined: 19 years ago
[#59252]
20261121 090604
20261121 090726
20261121 093726
20261121 090528
20261121 101250
20261121 101257
20261121 101331

I have redone my tree to a 180 format this year and I'm having so many configuration problems.

falcon f16v4 controller with additional 16

The tree is 48 strings of 144.

2 Strings are connected 144up 144down so each set has 288 pixels per string on 24 connectors.

V3 megapixeltree preview is set up as 48 string with 144 pix each

falcon controller software is set to 244px with 144zig on 24 outputs 

Hopefully the photos are helpful.

I welcome any configuration help


4 Replies
rayhjr
Posts: 973
(@rayhjr)
Noble Member
Joined: 12 years ago

When you patched the tree in V3 did you "Reverse Element Order" on all the Even numbered strings?

String 1 is up, 2 is down. 3 is up, 4 is down...........

Have you tried taking out the Zig-Zag in Falcon? 

 

Just throwing out ideas, but it does look like possible patching problem. Every other string is running opposite what it should be doing.


Reply
1 Reply
Mudsculpter
Admin
(@mudsculpter)
Joined: 19 years ago

Member
Posts: 1222

@rayhjr any idea is a good idea.


Reply
jeffu231
Posts: 2458
(@jeffu231)
Famed Member
Joined: 15 years ago

You have the zig zag configured in the controller, so you would not duplicate that in Vixen with reverse during patching. The controller is fine in that respect. The problem is the universe mapping. The first port starts on Universe 1 channel 1 and ends on Universe 2 channel 420. Assuming 510 in a universe, that universe 2 end should be 354 not 420. The controller calculates that based on the universe size setting. That is on the e1.31 tab assuming it is like my older ones. That needs to match what you are using in Vixen which should be 510 or 512. Assuming 510, you would need 40 universes of 510 channels and the last one 41 with 336. This gives you the 20,736 channels for 48 x 144 x 3. Validate the universe setup screen in Vixen looks like this. This is scrolled down, the other universes 1 - 27 are above that. 

image

 

Then in the controller ensure you have 41 universes allocated at 510 each in the e1.31 tab. Then go back to the string port tab and validate that the first port starts on universe 1 channel 1 and ends on Universe 2 channel 354. The next port should start on Universe 2 channel 355 not one like you have it. Each successive port starts on the same universe that the previous one ended on and one channel above the previous ports end channel. 

Give that a go and if you still have issues post the Vixen Universe setup page, the e1.31 tab of the controller, and the string setup of the controller. IF you did any reversing when patching in Vixen, you will need to undo that and then patch it straight through since the zig zag is in the controller.

 

EDIT: If this controller supports DDP, which it should, using DDP for the controller in Vixen and configuring the controller would simplify things. DDP does away with the whole universe config and just uses a block of channels. The controller setup should be much simpler as well. 


Reply
Mudsculpter
Posts: 1222
Admin
Topic starter
(@mudsculpter)
Member
Joined: 19 years ago

It does support DDP but I dont know how that works. Im going to use your instructions as written first and see if that gives joy. BTW the photo you posted doesnt show for me


Reply
Share: