Mega Tree plan - Do...
 
Notifications
Clear all

Mega Tree plan - Does this make sense?

3 Posts
3 Users
0 Reactions
1,483 Views
Posts: 225
 amps
Topic starter
(@amps)
Reputable Member
Joined: 15 years ago
[#37629]

Hey heidi ho!

So this is the year I make the delve into pixels. *Gasp*

I'm planning a 14ft, 16 string mega tree. I think I've got everything picked out and the planning right but I need some different eyes to see if I messed anything up.

I'm going to use the following:

-8 strings of 100 12v WS2811 Pixels

-2 of these 400w 12V power supplies

-6 Tee connectors with 2 pin in the middle for power injection

-A variety of 1ft and 5ft 3 pin connectors for stringing things together

-6 2 pin connectors for injecting power into Tees

-Sandevices E6804

The plan is to use two ports on the E6804, one for each half of the tree (180 degree section). Each string will be folded over at the top and come back down on the same side, connect to the next string and repeat. At each junction of strings (3 per side) I'll use Ray's Tee connectors with the 2 pin power connection to inject power from a PSU dedicated to that side. I calculate that each side will use a maximum of 240watts which leaves me lots of overhead on the 400w supplies.

Would it be worth it to inject power again at the end of each run? The way I have it planned currently, every pixel is with 50 nodes of a power line expect for the last half of the last string which is up to 100 nodes away. I figure 12V units should limit that to being a problem.

Would it be simpler (but more expensive) to use an E682? I could run each string of 100 independently from a port on the controller (4 from each power bank). Using 12V pixels, would that not alleviate the need for power injection?

Also, can Vixen 3 handle this way of running string? Reversing the order of each subsequent 50 pixels (up then down)?

Thanks!


2 Replies
Robo
Posts: 1494
 Robo
(@robo)
Noble Member
Joined: 14 years ago

My 2cents, e682 with 16 ports one to each 50 pixel string. No injection needed with 12 volts.


Reply
dgirard
Posts: 337
(@dgirard)
Reputable Member
Joined: 17 years ago

I'm currently running 120 12v pixels per channel. I've measured the voltage drop (with the pixels on all white) to be just about 4v...so at the start of the string I see 12v and at the end of the string it's 8-9v. If I'm not doing all white the drop is less. with no lights on, the voltage drop is about 1.5V (I measure about 10v at the end). This is using the Holiday-Coro bullet pixels--their wiring is something less than 18ga, and I'm guessing fairly typical.

The pixels seem to be working just fine with this voltage drop, so you should be fine with folding over and having 100 pixel runs.

You'll also probably find that your strings draw less power than their spec...Mine draw significantly less than I expected. Good idea to plan your power against the spec though--it give you that much more margin.

The nice thing about the e682 is that you'll have a fused power link to each string...with the 6804, you're only fusing the first run of power...unless you add additional in-line fuses everywhere you inject power. Unless you don't want that protection, you should add that to the cost of the 6804 in deciding just how much more expensive the 682 really is.

Good luck! The rest of your plan sounds spot on. Vixen can easily handle an up-down-up-down string arrangement. (I think the 6804 and 682 can also handle this for you--just pick one way of doing it!) xLights can also handle this. The only time I had a problem was when I needed to go up-down-up - up-down-up on the same string...I could do it with xLights, but I couldn't figure out how to do it with Vixen (without mapping each pixel individually--that can be done)


Reply
Share: