ninjinja wrote:Is there any ethernet options that are not USB? This project looks really good, so far I use RonP controllers, but am looking for something with some configurability, can this really drive 32 outputs? is there a theoretical limit of pixels with all channels driven?
You may be interested to look into http://doityourselfchristmas.com/forums/showthread.php?55073-Teensy-4-1-E1-31-receiver-controller
ninjinja wrote:Is there any ethernet options that are not USB? This project looks really good, so far I use RonP controllers, but am looking for something with some configurability, can this really drive 32 outputs? is there a theoretical limit of pixels with all channels driven?
On the first question: no. The network connection is via USB port. That said, because of that, you can use USB WIFI as well.
For the second question: Yes, the PocketBeagle can drive up to 40 outputs at full ws281x speed, with the limit of pixels being the speed of the ws281x protocol. At 40fps, that's 800 pixels. At 20fps, around 1600. Also, since it runs FPP, the amount of configuration and such that is available is significantly more that any other controller. You can add a USB sound card (need a USB hub for more USB ports) and it can be a full standalone show controller. All the various FPP plugins will work. It can run in standalone mode, master/remote setup, or bridge mode. Etc....
Just wanted to give a shout out to Scott and his Boards. I ran my show with several of the PB16 boards and they ran Great!
I had a PI3 as my Master and 2 Remotes. Remote 1 was PB16 Mini out to a Diff. Expansion board and then 2 Receiver out boards. One controlling some pixel floods and verticals near the house. The second controlled my Mega Tree. Three outputs for tree and one for Boscoyo 36' 270 pixel star. Tree and star all power injection. Tree, 24 strands of 74 or 12x148. Data at string 1, 5 and 9. Power on both ends of 148. Anyway, 592 pixels per port on tree and 270 on 1 port for star.
Remote 2 was a full PB16 out in the yard for 5 Mini Trees and stars, 4 arches, mini grid for tune to sign and 2 more Pixel Floods. I used 8 outputs and no power injection. Ran most at 25%, floods about 50%.
I ran my Renards, 3 RPLCC16's and a RPTR24, off remote 1, DMX.
It all ran Great. Thanks again for sharing this project with us. I for one really like it.
How did you connect up your Renards? How far away from the PB16?
rayhjr wrote:Just wanted to give a shout out to Scott and his Boards. I ran my show with several of the PB16 boards and they ran Great!
I had a PI3 as my Master and 2 Remotes. Remote 1 was PB16 Mini out to a Diff. Expansion board and then 2 Receiver out boards. One controlling some pixel floods and verticals near the house. The second controlled my Mega Tree. Three outputs for tree and one for Boscoyo 36' 270 pixel star. Tree and star all power injection. Tree, 24 strands of 74 or 12x148. Data at string 1, 5 and 9. Power on both ends of 148. Anyway, 592 pixels per port on tree and 270 on 1 port for star.
Remote 2 was a full PB16 out in the yard for 5 Mini Trees and stars, 4 arches, mini grid for tune to sign and 2 more Pixel Floods. I used 8 outputs and no power injection. Ran most at 25%, floods about 50%.
I ran my Renards, 3 RPLCC16's and a RPTR24, off remote 1, DMX.
It all ran Great. Thanks again for sharing this project with us. I for one really like it.
The PB16 and The PB16 Mini have 2 RJ-45 Connectors with DMX/LOR/Renard Wiring Support with a DPDT switch that goes between DMX and Renard on DMX2, and DMX and LOR on DMX1. The PB16 also has a DMX Fused Terminal Blocks that is connected (I Think) to DMX 2 only.
I put Renard DMX Firmware on my boards, and gave them start addresses. I used the Mini DMX2 out to my Renards. I made a special Cat5 wire that went from DMX to Renard going to my first RPLCC16 about 20' away, then regular Cat5 cables between the remaining Renards.
From GetHub page. I tried on both DMX and Renard (change switch positions) On DMX2 and it worked on Both (with special cable for each). The DMX2 has the (-) and (+) on opposite pins as DMX1, no biggie just make Cat5 cable accordingly.
Hope this answers your questions, if not let me know and I'll try again.

