rayhjr wrote:The PB16 and The PB16 Mini have 2 RJ-45 Connectors with DMX/LOR/Renard Wiring Support with a DPDT switch that goes between DMX and Renard on DMX2, and DMX and LOR on DMX1. The PB16 also has a DMX Fused Terminal Blocks that is connected (I Think) to DMX 2 only.
I put Renard DMX Firmware on my boards, and gave them start addresses. I used the Mini DMX2 out to my Renards. I made a special Cat5 wire that went from DMX to Renard going to my first RPLCC16 about 20' away, then regular Cat5 cables between the remaining Renards.From GetHub page. I tried on both DMX and Renard (change switch positions) On DMX2 and it worked on Both (with special cable for each). The DMX2 has the (-) and (+) on opposite pins as DMX1, no biggie just make Cat5 cable accordingly.
Hope this answers your questions, if not let me know and I'll try again.
I don't really know anything about Renard, but have several of the PB16 boards (and the various forms of it) built. I'd like to be able to control a few AC lights next year and was looking at the Renard. Are you saying that to be able to connect a Renard to the PB16, you MUST make a cable with 2 of the wires switched or is that only if you run it off of DMX2?
Also, can I run a Renard relay board (such as this: https://renard-plus.com/ssr8.html ) directly from the PB16 or do I still need a Renard controller?
And when you say "I put Renard DMX Firmware on my boards", do you mean that you put Renard DMX firmware on your PB16 mini's???
Glycerine wrote:I don't really know anything about Renard, but have several of the PB16 boards (and the various forms of it) built. I'd like to be able to control a few AC lights next year and was looking at the Renard. Are you saying that to be able to connect a Renard to the PB16, you MUST make a cable with 2 of the wires switched or is that only if you run it off of DMX2?
Also, can I run a Renard relay board (such as this: https://renard-plus.com/ssr8.html ) directly from the PB16 or do I still need a Renard controller?
And when you say "I put Renard DMX Firmware on my boards", do you mean that you put Renard DMX firmware on your PB16 mini's???
Maybe this will help. You have to make a special cable no matter what. You just have to know the pinout of the Output(PB16) and Receiver(Renard) to know how to make it.
This shows Data(+) pin 1 & Data(-) pin 2 and that is the way DMX1 is but DMX2 is Data(+) pin 2 & Data(-) pin1. (switch in DMX position) The RJ45 connector on the Left is the PB16 side and the connector on the Right is the Renard Board. PB16 DMX2 with the DPDT switch in the Renard position put Data(+) on pin5 & Data(-) on pin 4, matching the drawing. It is DMX either way. http://www.doityourselfchristmas.com/wiki/index.php?title=Renard_Data_Cables
That SSR board would still need a controller to output to it, something like a RP32, Rp16 or a Renard 64 like it says in the description.
http://www.renard-shop.com/relay-boards/6-8-channel-solid-state-relay-board.html
Any Renard or RP Controller would work. The DMX Firmware is on the Renard Controller. Wayne J. has the Renard SS8, SS16, and SS24 that would work, with the DMX firmware on it. http://doityourselfchristmas.com/forums/showthread.php?22450-SS-Renard-Kits-Now-Available
rayhjr wrote:Maybe this will help. You have to make a special cable no matter what. You just have to know the pinout of the Output(PB16) and Receiver(Renard) to know how to make it.This shows Data(+) pin 1 & Data(-) pin 2 and that is the way DMX1 is but DMX2 is Data(+) pin 2 & Data(-) pin1. (switch in DMX position) The RJ45 connector on the Left is the PB16 side and the connector on the Right is the Renard Board. PB16 DMX2 with the DPDT switch in the Renard position put Data(+) on pin5 & Data(-) on pin 4, matching the drawing. It is DMX either way. http://www.doityourselfchristmas.com/wiki/index.php?title=Renard_Data_Cables
That SSR board would still need a controller to output to it, something like a RP32, Rp16 or a Renard 64 like it says in the description.
http://www.renard-shop.com/relay-boards/6-8-channel-solid-state-relay-board.html
Any Renard or RP Controller would work. The DMX Firmware is on the Renard Controller. Wayne J. has the Renard SS8, SS16, and SS24 that would work, with the DMX firmware on it. http://doityourselfchristmas.com/forums/showthread.php?22450-SS-Renard-Kits-Now-Available
Yes, that helps. Thank you!
rayhjr wrote:Maybe this will help. You have to make a special cable no matter what. You just have to know the pinout of the Output(PB16) and Receiver(Renard) to know how to make it.This shows Data(+) pin 1 & Data(-) pin 2 and that is the way DMX1 is but DMX2 is Data(+) pin 2 & Data(-) pin1. (switch in DMX position) The RJ45 connector on the Left is the PB16 side and the connector on the Right is the Renard Board. PB16 DMX2 with the DPDT switch in the Renard position put Data(+) on pin5 & Data(-) on pin 4, matching the drawing. It is DMX either way. http://www.doityourselfchristmas.com/wiki/index.php?title=Renard_Data_Cables
That SSR board would still need a controller to output to it, something like a RP32, Rp16 or a Renard 64 like it says in the description.
http://www.renard-shop.com/relay-boards/6-8-channel-solid-state-relay-board.html
Any Renard or RP Controller would work. The DMX Firmware is on the Renard Controller. Wayne J. has the Renard SS8, SS16, and SS24 that would work, with the DMX firmware on it. http://doityourselfchristmas.com/forums/showthread.php?22450-SS-Renard-Kits-Now-Available
There was a wiring mistake on the on the PB16 Mini. I just fixed it after you pointed it out. Both DMX RJ45 ports should have Data(+) as pin 1 & Data(-) as pin 2. On the "main" PB16 it was already wired correctly. I know DMX2 works with the Renard pinout as I use it with a Renard 8 controller flashed with the DMX firmware.
Thanks,
Scott
Hi Scott & PB16 Experts -
Quick question on the circuit design - what is the EEPROM IC for - what data is flashed on to it, what does it enable the board to do?
Thank you!

