Question on only us...
 
Notifications
Clear all

Question on only using data from controller

36 Posts
8 Users
0 Reactions
5,947 Views
Posts: 37
Topic starter
(@tbm878)
Trusted Member
Joined: 9 years ago

Maybe this will help. The first option has me running a single 18-3 cable from the controller box to the first pixel. And not running a V- from the controller, only a V- from the power distro board. This 18-3 cable will vary in length from 20-40' long....

20220201 115255

This is option #2, it might require a second 18-3 cable and a tee to be used at the first pixel. Another option is could i run the controller signal V- and splice it to the V- coming from the power distro board? This would only need 1 18-3 cable going to the first pixel....

20220201 112930

I definitely want to do this the safe way. And i understand its best to run a V- from the controller, I'm just trying to see the best way to do it without having extra splices and extra cables. Do they make xConnect 4 wire extension cords?

Thanks,
Tim


Reply
Posts: 105
(@pakeonoahu)
Estimable Member
Joined: 11 years ago

I ran 45ft 12AWG power cable pairs from my power supply to my first pixel, there's no way by running a single data wire to my first pixel would work, but I have no issue running twisted pair on a CAT5 cable from the controller using V- and Data. my dual 12AWG power cables are on disputation for 1k 5V pixels, as with power draw on different sequences, the power V-(GND) reference will change due to resistance in the wire, where a single data wire will see the reference change plus environment EMI, when it's on the twisted pair, the ground(V-) reference will not change much because there's no current draw from that port, and the EMI will cancelled out on the twisted pair where the single data wire will act as an antenna(convert EMI to electricity, either riding above or inverted to your data signal), if you are talking about just few feet, go ahead and it likely will work but are you saving that much for few feet of 24AWG wire?


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 19 years ago
tbm878 wrote:Maybe this will help. The first option has me running a single 18-3 cable from the controller box to the first pixel. And not running a V- from the controller, only a V- from the power distro board. This 18-3 cable will vary in length from 20-40' long....

This is option #2, it might require a second 18-3 cable and a tee to be used at the first pixel. Another option is could i run the controller signal V- and splice it to the V- coming from the power distro board? This would only need 1 18-3 cable going to the first pixel....

I definitely want to do this the safe way. And i understand its best to run a V- from the controller, I'm just trying to see the best way to do it without having extra splices and extra cables. Do they make xConnect 4 wire extension cords?

Thanks,
Tim

Option 1 is very much sub-optimal, it might work fine right up the time that you first go live after Thanksgiving.

Option 2 - is much better - run the V- from the controller to the first pixel. The wire from the controller to the distribution board is not necessary.

Neither option is totally to my liking, though. If it were my setup I'd prefer to have complete electrical isolation between the controller and the first pixel for both the data and v- lines between the two. The reason that I say this is to guarantee that current for the pixel strings never flows through the ground wire between the controller and the pixel string. Normally this wouldn't happen because the wire gauges are sufficiently different that the current 'wants' to flow through the thick power leads; however, if one of those leads becomes broken or cut, the heavy ground current to the pixels might take the alternate path through the controller->pixel ground wire. In this situation the pixels would still appear to mostly work, but would be flaky, and you wouldn't know to look for cut/broken main ground leads. You would have a much easier time tracking down the problem if that sneak path did not exist, because entire string(s) would fail, rather than just being flaky.


Reply
MartinMueller2003
Posts: 7612
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

In my show I use a small 10W supply to power the controller and there is no (direct) connection to the PSU that drives the pixels.


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 19 years ago
MartinMueller2003 wrote:In my show I use a small 10W supply to power the controller and there is no (direct) connection to the PSU that drives the pixels.

That's a good way to do it. It's not what I was thinking, but it certainly works, and has the advantage that the controller stays up even if the PSUs for the strings goes down.


Reply
Page 3 / 8
Share: