Having problems usi...
 
Notifications
Clear all

Having problems using a E6804 and E682 in the setup

24 Posts
7 Users
0 Reactions
6,716 Views
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago
11Bravo wrote:thank you for the link, I got the E682 upgraded to version 5.030. After some hours I think I got the configuration correct. I tested each output with pixel strings. I only had four spares to work with so I did four outputs at a time. I'm not good on the math part as far as selecting the correct Universes but I think from the test it is correct accidentally. I did it in Multicast first, Then change to Unicast in the xlights setup and on the E682, but couldn't get outputs to come on. I'm sure there is something I'm not doing right.
I'm going to give the E6804 another go a configuring it before I try to upgrade the firmware on it.

E682 configuration:

That looks much better. If you have problems with the lights try setting the timing higher. Usually 200 and up.

Sent from my SM-T710 using Tapatalk


Reply
Posts: 1115
Topic starter
(@11bravo)
Noble Member
Joined: 14 years ago

I forgot to add a note and edited the attachment in red text.


Reply
Posts: 1115
Topic starter
(@11bravo)
Noble Member
Joined: 14 years ago
MikeKrebs wrote:in xlights, be sure to turn on output...lightbulb top right usually.

yeah, that will getcha everytime. Reading Xenia's demise, after upgrading firmware on his sandevices isn't very hopeful.

Next up is, trying to get the E6804 to drive my window frames. I did not up grade it yet.

I have configured the 1st output, at Universe 7 and starting at channel 391 continuing from the last configuration of the E682, which is universe 7, channel 390.
Only the 3 sides of the window frame light up. I change the numbers in the channel and the universe but can't make all the pixels light up. Alll the pixels are good from a test standpoint. And I even swapped them out with another frame of same number.
I reconfigure the model in xlights to a single line, but that doesn't solve anything.
So here we are stuck again.


Reply
Posts: 740
(@ezellner)
Prominent Member
Joined: 11 years ago
11Bravo wrote:yeah, that will getcha everytime. Reading Xenia's demise, after upgrading firmware on his sandevices isn't very hopeful.

Next up is, trying to get the E6804 to drive my window frames. I did not up grade it yet.

I have configured the 1st output, at Universe 7 and starting at channel 391 continuing from the last configuration of the E682, which is universe 7, channel 390.
Only the 3 sides of the window frame light up. I change the numbers in the channel and the universe but can't make all the pixels light up. Alll the pixels are good from a test standpoint. And I even swapped them out with another frame of same number.
I reconfigure the model in xlights to a single line, but that doesn't solve anything.
So here we are stuck again.

Are you sure you have the right number of pixels entered? Sounds as if you're just a few short in your set up.


Reply
Posts: 1115
Topic starter
(@11bravo)
Noble Member
Joined: 14 years ago

window frame is a total of 58 pixels. Top and bottom 11 each = 22, Rt and Lt side 18 each= 36. I reconfigure for a single Line of 58 pixels, and that doesn't make any difference either.
I can change the channel number in the controller minus or plus pixels. That changes the pixels either back or forward, and or changes the color. They are 12 volt square WS2811 type. The color type of the string doesn't seem to be RGB because I have to make the color come out right by changing the type in the controller parameter.

has there been a problem with new 12volt pixels not working correctly in sandevices or other controllers?


Reply
Page 4 / 5
Share: