shelby, I have a Pro DMX fixture I'd like to try to use one of these on. Any suggestions on if/how I can do that. The outputs from the pixel Stick are V+, Gnd, D+, Clk. For a DMX fixture it's GND, D+, D-.
*I also Posted this in the Forum: The Beginning, hope this is not in any violation of Forum Rules*
Hello!
I have, what seems to me, a pretty simple problem. However after a few weeks of researching I am at my wits end!
I am building a large computer desk and cupboards for my Wife and I's gaming room. I am building some WS2812 LED strips into the edges of the desk with a PvC diffuser over them.
I am going to have some running along the bottom, and some on the top. Also in the corner I am going to make some edge lite shelves.
Here is a basic drawing of what I am going to do, the red lines are the strings of LED's:
All I want to do is have a few chasing patterns and simple things like that setup and able to be run/changed via a desktop app or a Web Interface.
I have an ESPixelStick as a controller, a 5v 60w PSU, lots of wire and the LED's. I've got those hooked up and running the test patterns. I think I,m good on the hardware end, I'm somewhat knowledgeable in that department.
However, coding/software is beyond me, and I really do NOT want to spend any time monkeying with it. I cannot find any software that is intended for this type of thing. Vixen, xlights, ect, I have downloaded and checked out. WAY more than I need, and much too complicated to bother learning for this small project (I think...)
Anyway, do any of you know of a good solution for this? I'll take any and all recommendations! I"ll post a few examples of what I'm looking for down below:
Firstly it would be VERY nice to be able to Download and make my own Patterns via this website (or something similar):
https://hohmbody.com/flickerstrip/lightwork/
Something like this would be amazing too:
And then some type of interface where I just select the chase pattern and it plays.
I know this is probably alittle too simple of a project to be posting here, but I just cannot find anything elsewhere that does not require a substantial amount of coding.
Thank You so much for taking the time to read this, and for any help/advice you may be able to give.
-Kevin
Photon wrote:*I also Posted this in the Forum: The Beginning, hope this is not in any violation of Forum Rules*Hello!
I have, what seems to me, a pretty simple problem. However after a few weeks of researching I am at my wits end!
I am building a large computer desk and cupboards for my Wife and I's gaming room. I am building some WS2812 LED strips into the edges of the desk with a PvC diffuser over them.
I am going to have some running along the bottom, and some on the top. Also in the corner I am going to make some edge lite shelves.
Here is a basic drawing of what I am going to do, the red lines are the strings of LED's:
All I want to do is have a few chasing patterns and simple things like that setup and able to be run/changed via a desktop app or a Web Interface.
I have an ESPixelStick as a controller, a 5v 60w PSU, lots of wire and the LED's. I've got those hooked up and running the test patterns. I think I,m good on the hardware end, I'm somewhat knowledgeable in that department.
However, coding/software is beyond me, and I really do NOT want to spend any time monkeying with it. I cannot find any software that is intended for this type of thing. Vixen, xlights, ect, I have downloaded and checked out. WAY more than I need, and much too complicated to bother learning for this small project (I think...)
Anyway, do any of you know of a good solution for this? I'll take any and all recommendations! I"ll post a few examples of what I'm looking for down below:
Firstly it would be VERY nice to be able to Download and make my own Patterns via this website (or something similar):
https://hohmbody.com/flickerstrip/lightwork/
Something like this would be amazing too:
And then some type of interface where I just select the chase pattern and it plays.
I know this is probably alittle too simple of a project to be posting here, but I just cannot find anything elsewhere that does not require a substantial amount of coding.
Thank You so much for taking the time to read this, and for any help/advice you may be able to give.
-Kevin
Sounds like the solution you’re looking for is not really a good fit for an espixelstick (or any other streaming lighting controller for that matter)
We can come up with solutions to do this sort of thing with controllers and players common around here but it’s going to be a lot more elaborate of a solution than you need or want.
What you really want is a standalone player that can be easily triggered to play out canned patterns. The T1000s might suit you well.
Sent from my iPhone using Tapatalk
michaelc wrote:shelby, I have a Pro DMX fixture I'd like to try to use one of these on. Any suggestions on if/how I can do that. The outputs from the pixel Stick are V+, Gnd, D+, Clk. For a DMX fixture it's GND, D+, D-.
You can do that by loading the serial firmware on the ESPixelStick, however you need to feed the data line through an RS485 module to get your differential D+/D- signals. I wrote up a howto here on it - https://diychristmas.org/vb1/showthread.php?7274-ESPixelStick-RS485-DMX-Hack . That's how I control the DM-103 DMX encoders for my window washers during Halloween.
Photon wrote:*I also Posted this in the Forum: The Beginning, hope this is not in any violation of Forum Rules*Hello!
I have, what seems to me, a pretty simple problem. However after a few weeks of researching I am at my wits end!
I am building a large computer desk and cupboards for my Wife and I's gaming room. I am building some WS2812 LED strips into the edges of the desk with a PvC diffuser over them.
I am going to have some running along the bottom, and some on the top. Also in the corner I am going to make some edge lite shelves.
Here is a basic drawing of what I am going to do, the red lines are the strings of LED's:
All I want to do is have a few chasing patterns and simple things like that setup and able to be run/changed via a desktop app or a Web Interface.
I have an ESPixelStick as a controller, a 5v 60w PSU, lots of wire and the LED's. I've got those hooked up and running the test patterns. I think I,m good on the hardware end, I'm somewhat knowledgeable in that department.
However, coding/software is beyond me, and I really do NOT want to spend any time monkeying with it. I cannot find any software that is intended for this type of thing. Vixen, xlights, ect, I have downloaded and checked out. WAY more than I need, and much too complicated to bother learning for this small project (I think...)
Anyway, do any of you know of a good solution for this? I'll take any and all recommendations! I"ll post a few examples of what I'm looking for down below:
Firstly it would be VERY nice to be able to Download and make my own Patterns via this website (or something similar):
https://hohmbody.com/flickerstrip/lightwork/
Something like this would be amazing too:
And then some type of interface where I just select the chase pattern and it plays.
I know this is probably alittle too simple of a project to be posting here, but I just cannot find anything elsewhere that does not require a substantial amount of coding.
Thank You so much for taking the time to read this, and for any help/advice you may be able to give.
-Kevin
Kevin may be something on this page would work for you
http://www.ebay.com/bhp/led-pixel-controller
sporadic wrote:You can do that by loading the serial firmware on the ESPixelStick, however you need to feed the data line through an RS485 module to get your differential D+/D- signals. I wrote up a howto here on it - https://diychristmas.org/vb1/showthread.php?7274-ESPixelStick-RS485-DMX-Hack . That's how I control the DM-103 DMX encoders for my window washers during Halloween.
That is friggin awesome.....I have 8 or 9 of the DM-103's in a drawer just itching to get used. This is a great mod.
Thanks.
jchuchla wrote:Sounds like the solution you’re looking for is not really a good fit for an espixelstick (or any other streaming lighting controller for that matter)
We can come up with solutions to do this sort of thing with controllers and players common around here but it’s going to be a lot more elaborate of a solution than you need or want.
What you really want is a standalone player that can be easily triggered to play out canned patterns. The T1000s might suit you well.Sent from my iPhone using Tapatalk
Thanks for taking the time to respond Jon. I had looked at the T1000s, almost sprung but I went with the espixelstick because of the WiFi and customizability of patterns/interfaces.
I looked at the T1000s and some of its cousins again and that gave me renewed motivation to figure this thing out! Was up till 6am setting up the stick and all the arduino stuff. I thought everything was in the firmware and I was just not understanding how to bring it all together. Got a ways to go, but I know which direction I'm headed now at least 🙂
Thanks!
-Kevin
PS. Out of curiosity, would it be possible to get ahold of, say, a modified Flickerstrip, or even T1000s firmware and load it onto the espixelstick so that it acts like a flickerstrip e1.31 controller that could be driven by software Lightworks or LEDedit?
Now your asking for something else entirely. If you can get the specification for the protocol used between the player and the controller, that would be something that can be added to the ESP code. As it is, I use the ESP to control lights in the dining room with various relaxing color combinations and changes. The ESP is a platform. If you remove the E1.31 code you can pretty much add anything you want.
Thanks Bob,
Thats exactly where I'm heading if I get frustrated by this one more time 😛
appreciate the link!
-Kevin
Photon wrote:*I also Posted this in the Forum: The Beginning, hope this is not in any violation of Forum Rules*Hello!
I have, what seems to me, a pretty simple problem. However after a few weeks of researching I am at my wits end!
I am building a large computer desk and cupboards for my Wife and I's gaming room. I am building some WS2812 LED strips into the edges of the desk with a PvC diffuser over them.
...
And then some type of interface where I just select the chase pattern and it plays.
I know this is probably alittle too simple of a project to be posting here, but I just cannot find anything elsewhere that does not require a substantial amount of coding.
Thank You so much for taking the time to read this, and for any help/advice you may be able to give.
-Kevin
simple Arduino with examples?
https://www.tweaking4all.com/hardware/arduino/arduino-ws2812-led/

