Activity
 
Notifications
Clear all
michaelc
michaelc
@michaelc
Noble Member
Joined: May 30, 2007
Topics: 128 / Replies: 1412
Reply
RE: Wow, just wow... I received this email from David Moore at HolidayCoro

Dan, JIm, That just sucks all around. After the bad service on a few simple coro products from them I never even considered buying anything meaningfu...

4 years ago
Forum
Reply
RE: RenardESP Information Thread

Not a dumb question. I've been wondering since March.

8 years ago
Forum
Reply
RE: Pixiflood 10w Floodlight Driver (WS2811)

I've bought all my 10W boards from RobG on Tindie. Is he on this forum? Anyone know where I can get my hands on 4 more boards. I'd settle for the P...

8 years ago
Reply
RE: RenardESP Information Thread

So this solves the issue that if you use a RENESP, you can't daisy chain downstream?

9 years ago
Forum
Reply
RE: How many RBL's at $4.00 did you buy?

I had 10 shipped to my house at the $4 rate. If you look now, they are $2 but out of stock. I use the rectangular pixel nodes in mine so I'm torn b...

9 years ago
Forum
Reply
RE: ESPixelStick - E1.31 WiFi Pixel Controller

shelby, I have a Pro DMX fixture I'd like to try to use one of these on. Any suggestions on if/how I can do that. The outputs from the pixel Stick ...

9 years ago
Reply
RE: ESPixelStick - E1.31 WiFi Pixel Controller

What's the latest firmware version for the ESPIXELSTICK and where is it? Is the one on FORKINEYE still the latest?

9 years ago
Reply
RE: RENESP Renard ESP8266 WiFi Adapter Group Buy for PCB and BOM

MartinMueller2003 wrote:It all depends on the hardware design. The Renard devices use simplex communications, the device only receives data. The devic...

9 years ago
Forum
Reply
RE: RENESP Renard ESP8266 WiFi Adapter Group Buy for PCB and BOM

I can see why it would NOT work in THRU mode. Once you set it to THRU mode, there is no path from the input RS485 header to the Output RJ45 connector...

9 years ago
Forum
Reply
RE: 10W RGB LED driver boards (Ren/dumb RGB, WS2811, DMX)

So I have the original RED 10W boards. They are connected to my REN48LSD using a breakout board. From my FPP I can do a test and all the colors are ...

9 years ago
Reply
RE: RENESP Renard ESP8266 WiFi Adapter Group Buy for PCB and BOM

I have a RENESP question and I'm not sure what the right place to ask is. Here is what I have. I have a RENESP connected to a REN4FLOOD. The REN4FL...

9 years ago
Forum
Reply
RE: RenardESP new firmware. Testers required

I re-flashed the 2-1 and it seems to be working. Thanks.

9 years ago
Forum
Reply
RE: RenardESP new firmware. Testers required

Can someone tell me what the latest version should be. I used the tool and flashed the board and it loaded 2.1-dev (20161214). This version has the ...

9 years ago
Forum
Reply
RE: RenardESP new firmware. Testers required

Ok, I'm just getting back (finally) to my Ren4Flood boards. Basically Renard boards running the DMX code. I have original RENESP REV E boards that ...

9 years ago
Forum
Reply
RE: RenardESP Information Thread

I'm just getting back to my RENESP now. I have Bill Porters RENESP. What and where is the correct Arduino Sketch to load onto these. Are these stil...

9 years ago
Forum
Page 1 / 103
Share: