ESPixelStick - E1.3...
 
Notifications
Clear all

ESPixelStick - E1.31 WiFi Pixel Controller

948 Posts
178 Users
0 Reactions
503.8 K Views
Posts: 11
(@artem)
Active Member
Joined: 9 years ago
Photon wrote:

PS. Out of curiosity, would it be possible to get ahold of, say, a modified Flickerstrip, or even T1000s firmware and load it onto the espixelstick so that it acts like a flickerstrip e1.31 controller that could be driven by software Lightworks or LEDedit?

This controller is based on esp8266 maybe something will come up. See item description
https://www.aliexpress.com/item/led-wifi-controller-one-phone-does-all-jobs-drive-max-2048-pixels-support-dozens-of-chips/32817737225.html


Reply
Posts: 11
(@artem)
Active Member
Joined: 9 years ago

My Led matrix 73*40. ws2812b 5 volt. Power injector every two lines (2,5 m = 300 pixels)
1 pcs esp8266 with firmware from ESPixelStick support 1360 pixels. Thank you to the Creator ESPixelStick firmware.
But hardware i use wemos d1 and d1 mini

photo 2017 11 03 04 31 29

photo 2017 11 03 04 31 37


Reply
sporadic
Posts: 1199
Topic starter
(@sporadic)
Noble Member
Joined: 14 years ago
artem wrote:My Led matrix 73*40. ws2812b 5 volt. Power injector every two lines (2,5 m = 300 pixels)
1 pcs esp8266 with firmware from ESPixelStick support 1360 pixels. Thank you to the Creator ESPixelStick firmware.
But hardware i use wemos d1 and d1 mini

Awesome, I need to build a bigger test matrix now! lol
thanks,
-shelby


Reply
Posts: 149
(@bob81354)
Estimable Member
Joined: 15 years ago
artem wrote:My Led matrix 73*40. ws2812b 5 volt. Power injector every two lines (2,5 m = 300 pixels)
1 pcs esp8266 with firmware from ESPixelStick support 1360 pixels. Thank you to the Creator ESPixelStick firmware.
But hardware i use wemos d1 and d1 mini

Nice job can you tell us what you are using for the backer board and how you attached them


Reply
Posts: 11
(@artem)
Active Member
Joined: 9 years ago
sporadic wrote:Awesome, I need to build a bigger test matrix now! lol
thanks,
-shelby

240 cm * 124 cm (95 inch * 50 inch)

photo 2017 11 04 22 50 22

Reply
Posts: 11
(@artem)
Active Member
Joined: 9 years ago
bob81354 wrote:Nice job can you tell us what you are using for the backer board and how you attached them

I don't know what it might be name from you, so better links
https://leroymerlin.ru/product/stepler-ruchnoy-tip-53-dexter-pod-skoby-6-14-mm-gvozdi-8-9-mm-15077861/
https://leroymerlin.ru/catalogue/osp-3/
the tape was glued and then stapled
Sorry for my English

photo 2017 11 04 23 28 17
photo 2017 11 04 23 28 23
photo 2017 11 04 23 28 28
photo 2017 11 04 23 33 43

Reply
Posts: 11
(@artem)
Active Member
Joined: 9 years ago
Reply
Posts: 11
(@artem)
Active Member
Joined: 9 years ago

sporadic
If replace the esp8266 on esp32 how many pixels esp32 will be able to support?
There processor esp32 is better.


Reply
sporadic
Posts: 1199
Topic starter
(@sporadic)
Noble Member
Joined: 14 years ago
artem wrote:sporadic
If replace the esp8266 on esp32 how many pixels esp32 will be able to support?
There processor esp32 is better.

There's a lot to be done for ESP32 support. Still lots of issues in the core and all the libraries need to be ported to it.


Reply
Posts: 11
(@artem)
Active Member
Joined: 9 years ago

My first soldering . First experience homemade DIY

photo 2017 11 12 03 13 24

Two libraries to choose:
ArtNet - D4 (GPIO2)
E1.31 - D2 (GPIO4) by http://forkineye.com


Reply
Page 81 / 95
Share: