qawsed55 wrote:Hello!
Sorry for pore English.
I'm trying to test subj on Witty Cloud board
I have tried last version from github. After flashing board with ESPSFlashTool.jar it connects to my Wi-Fi network, that work on my android phone.
In web interface I try test. Its work ok. When I try to setup ArtNet - there are mistakes on web interface - dropdown menus are empty (color order and other).
After reboot - ESPPxStick connecting to android acces point, but after 3-4 sec it reboots in cycle.
Serial Monitor show this exceptions:ESPixelStick v3.0-rc3 (20170805) - Configuration loaded. Connecting to novorossia1 as esps-181599 Connecting with DHCP......... Connected with IP: 192.168.43.146 - Web Server started on port 80 - Listening for 1 channels, from Universe 1 to 1 - Unicast port: 5568 Exception (29): epc1=0x402083b4 epc2=0x00000000 epc3=0x00000000 excvaddr=0x00000000 depc=0x00000000 ctx: cont sp: 3fff1150 end: 3fff15d0 offset: 01a0 >>>stack>>> 3fff12f0: 3fff01b4 3fff0244 3fff011c 4020830c 3fff1300: 00001000 2d435341 312e3145 00000037 3fff1310: 00006c72 ee110400 41b720c6 e8a04914 3fff1320: 2326a022 56726c81 02000000 65786956 3fff1330: 0033206e 00000000 00000000 00000000 3fff1340: 00000000 00000000 00000000 00000000 3fff1350: 00000000 00000000 00000000 00000000 3fff1360: 00000000 00000000 00000000 ce000064 3fff1370: 72010000 00a10209 01010000 ff0000ff 3fff1380: 0000ff00 ff00ff00 ff000000 0000ff00 3fff1390: ff00ff00 ff000000 0000ff00 ff00ff00 3fff13a0: ff000000 0000ff00 ff00ff00 ff000000 3fff13b0: 0000ff00 ff00ff00 ff000000 0000ff00 3fff13c0: ff00ff00 ff000000 0000ff00 ff00ff00 3fff13d0: ff000000 0000ff00 ff00ff00 ff000000 3fff13e0: 0000ff00 ff00ff00 ff000000 0000ff00 3fff13f0: ff00ff00 ff000000 0000ff00 ff00ff00 3fff1400: ff000000 0000ff00 ff00ff00 ff000000 3fff1410: 0000ff00 ff00ff00 ff000000 0000ff00 3fff1420: ff00ff00 ff000000 0000ff00 ff00ff00 3fff1430: ff000000 0000ff00 ff00ff00 ff000000 3fff1440: 0000ff00 ff00ff00 ff000000 0000ff00 3fff1450: ff00ff00 ff000000 0000ff00 ff00ff00 3fff1460: ff000000 0000ff00 ff00ff00 ff000000 3fff1470: 0000ff00 ff00ff00 ff000000 0000ff00 3fff1480: ff00ff00 ff000000 0000ff00 ff00ff00 3fff1490: ff000000 0000ff00 ff00ff00 ff000000 3fff14a0: 0000ff00 ff00ff00 ff000000 0000ff00 3fff14b0: ff00ff00 ff000000 0000ff00 ff00ff00 3fff14c0: ff000000 0000ff00 ff00ff00 ff000000 3fff14d0: 0000ff00 ff00ff00 ff000000 0000ff00 3fff14e0: ff00ff00 ff000000 0000ff00 ff00ff00 3fff14f0: ff000000 0000ff00 ff00ff00 ff000000 3fff1500: 0000ff00 ff00ff00 ff000000 0000ff00 3fff1510: ff00ff00 ff000000 0000ff00 ff00ff00 3fff1520: ff000000 0000ff00 ff00ff00 ff000000 3fff1530: 0000ff00 ff00ff00 ff000000 0000ff00 3fff1540: ff00ff00 ff000000 0000ff00 ff00ff00 3fff1550: ff000000 0000ff00 ff00ff00 ff000000 3fff1560: 0000ff00 ff00ff00 ff000000 0000ff00 3fff1570: ff00ff00 ff000000 0000ff00 40210000 3fff1580: 00000000 00000000 feefeffe feefeffe 3fff1590: feefeffe feefeffe feefeffe feefeffe 3fff15a0: 00000000 00000000 00000001 3fff05a4 3fff15b0: 3fffdad0 00000000 3fff059d 40217888 3fff15c0: feefeffe feefeffe 3fff05b0 4010070c <<<stack<<< ets Jan 8 2013,rst cause:2, boot mode:(3,6) load 0x4010f000, len 1384, room 16 tail 8 chksum 0x2d csum 0x2d v00000000 ~ld ESPixelStick v3.0-rc3 (20170805) - Configuration loaded. Connecting to novorossia1 as esps-181599 Connecting with DHCP....... Connected with IP: 192.168.43.146 - Web Server started on port 80 - Listening for 1 channels, from Universe 1 to 1 - Unicast port: 5568 Exception (29): epc1=0x402083b4 epc2=0x00000000 epc3=0x00000000 excvaddr=0x00000000 depc=0x00000000 ctx: cont sp: 3fff1150 end: 3fff15d0 offset: 01a0 >>>stack>>> 3fff12f0: 3fff01b4 3fff0244 3fff011c 4020830c 3fff1300: 00001000 2d435341 312e3145 00000037 3fff1310: 00006c72 ee110400 41b720c6 e8a04914 3fff1320: 2326a022 56726c81 02000000 65786956 3fff1330: 0033206e 00000000 00000000 00000000 3fff1340: 00000000 00000000 00000000 00000000 3fff1350: 00000000 00000000 00000000 00000000 3fff1360: 00000000 00000000 00000000 3d000064 3fff1370: 72010000 00a10209 01010000 00ff00ff 3fff1380: 00ff0000 000000ff 00ff00ff 00ff0000 3fff1390: 000000ff 00ff00ff 00ff0000 000000ff 3fff13a0: 00ff00ff 00ff0000 000000ff 00ff00ff 3fff13b0: 00ff0000 000000ff 00ff00ff 00ff0000 3fff13c0: 000000ff 00ff00ff 00ff0000 000000ff 3fff13d0: 00ff00ff 00ff0000 000000ff 00ff00ff 3fff13e0: 00ff0000 000000ff 00ff00ff 00ff0000 3fff13f0: 000000ff 00ff00ff 00ff0000 000000ff 3fff1400: 00ff00ff 00ff0000 000000ff 00ff00ff 3fff1410: 00ff0000 000000ff 00ff00ff 00ff0000 3fff1420: 000000ff 00ff00ff 00ff0000 000000ff 3fff1430: 00ff00ff 00ff0000 000000ff 00ff00ff 3fff1440: 00ff0000 000000ff 00ff00ff 00ff0000 3fff1450: 000000ff 00ff00ff 00ff0000 000000ff 3fff1460: 00ff00ff 00ff0000 000000ff 00ff00ff 3fff1470: 00ff0000 000000ff 00ff00ff 00ff0000 3fff1480: 000000ff 00ff00ff 00ff0000 000000ff 3fff1490: 00ff00ff 00ff0000 000000ff 00ff00ff 3fff14a0: 00ff0000 000000ff 00ff00ff 00ff0000 3fff14b0: 000000ff 00ff00ff 00ff0000 000000ff 3fff14c0: 00ff00ff 00ff0000 000000ff 00ff00ff 3fff14d0: 00ff0000 000000ff 00ff00ff 00ff0000 3fff14e0: 000000ff 00ff00ff 00ff0000 000000ff 3fff14f0: 00ff00ff 00ff0000 000000ff 00ff00ff 3fff1500: 00ff0000 000000ff 00ff00ff 00ff0000 3fff1510: 000000ff 00ff00ff 00ff0000 000000ff 3fff1520: 00ff00ff 00ff0000 000000ff 00ff00ff 3fff1530: 00ff0000 000000ff 00ff00ff 00ff0000 3fff1540: 000000ff 00ff00ff 00ff0000 000000ff 3fff1550: 00ff00ff 00ff0000 000000ff 00ff00ff 3fff1560: 00ff0000 000000ff 00ff00ff 00ff0000 3fff1570: 000000ff 00ff00ff 00ff0000 40210000 3fff1580: 00000000 00000000 feefeffe feefeffe 3fff1590: feefeffe feefeffe feefeffe feefeffe 3fff15a0: 00000000 00000000 00000001 3fff05a4 3fff15b0: 3fffdad0 00000000 3fff059d 40217888 3fff15c0: feefeffe feefeffe 3fff05b0 4010070c <<<stack<<< ets Jan 8 2013,rst cause:2, boot mode:(3,6) load 0x4010f000, len 1384, room 16 tail 8 chksum 0x2d csum 0x2d v00000000 ~ldIs there troubles with module? May be it is uncompatible with subj firmware?
Thanks!
The binaries with the Jar tool are complied for esp-01, the unit you have is esp-12, I had problem with esp-01 firmware loaded on esp-12 in the past, you can install the Arduino SDK, and set it to use esp-12, 160Mhz, 3M/1M (1M for spiffs data), compile and install, then upload spiffs data. All my ESP-12 modules are working fine with this setting, if you are going to use OTA update, you will need to adjust the .json file in the firmware directory to reflect correct spiffs address before generating the OTA file.
pakeonoahu wrote:The binaries with the Jar tool are complied for esp-01, the unit you have is esp-12, I had problem with esp-01 firmware loaded on esp-12 in the past, you can install the Arduino SDK, and set it to use esp-12, 160Mhz, 3M/1M (1M for spiffs data), compile and install, then upload spiffs data. All my ESP-12 modules are working fine with this setting, if you are going to use OTA update, you will need to adjust the .json file in the firmware directory to reflect correct spiffs address before generating the OTA file.
That's unusual, I have used the jar tool with 6 esp-12 modules without any issues or modification of the code. They all work fine.
Sent from my SM-G900V using Tapatalk
sporadic wrote:Are you compiling youself and loading from the Arduino IDE? If so, there's an exception decoder tool that you can paste the stack trace into - https://github.com/me-no-dev/EspExceptionDecoder . If not, post the stack trace here from the pre-compiled 3.0-rc3 and will see if I can decode it. The smaller modules may work until you try to do an OTA upgrade, then things will go sideways.
Here's an update. If I manually edit the config.json file with the e1.31 parameters, the new black modules work fine, even after rebooting. However, if i make any changes via the web interface then it goes into a reboot loop with the exception (28) error.
EE351 wrote:That's unusual, I have used the jar tool with 6 esp-12 modules without any issues or modification of the code. They all work fine.Sent from my SM-G900V using Tapatalk
That's my experience too, only I used 30...
EE351 wrote:Here's an update. If I manually edit the config.json file with the e1.31 parameters, the new black modules work fine, even after rebooting. However, if i make any changes via the web interface then it goes into a reboot loop with the exception (28) error.
If you are talking about the ESP-12, I recalled Shelby mention some uses QIO for the flash, esp-01 uses DIO, so when writing to the flash with the wrong mode could cause issue, that can be changed from the Arduino IDE. My experience with the ESP-12 issue was programming them in version 2.x since all my 3.0-rc3 firmware on ESP-12 were upgraded via OTA, with layout 3M/1M spiffs, no issue at all. I have never try OTA upgrade on the ESP-12 using ESP-01 complied binaries, so don't know if that works or not.
pakeonoahu wrote:If you are talking about the ESP-12, I recalled Shelby mention some uses QIO for the flash, esp-01 uses DIO, so when writing to the flash with the wrong mode could cause issue, that can be changed from the Arduino IDE. My experience with the ESP-12 issue was programming them in version 2.x since all my 3.0-rc3 firmware on ESP-12 were upgraded via OTA, with layout 3M/1M spiffs, no issue at all. I have never try OTA upgrade on the ESP-12 using ESP-01 complied binaries, so don't know if that works or not.
The modules I'm having trouble with are some new esp-01 I recently purchased.
EE351 wrote:The modules I'm having trouble with are some new esp-01 I recently purchased.
There seems to be ESP-01 modules in that utilize different flash chips (DIO vs QIO). Bill ran into some a while back and was having issues - https://github.com/forkineye/ESPixelStick/issues/44 .
-shelby
sporadic wrote:There seems to be ESP-01 modules in that utilize different flash chips (DIO vs QIO). Bill ran into some a while back and was having issues - https://github.com/forkineye/ESPixelStick/issues/44 .
-shelby
Does the jar tool use a different flash mode vs the web configuration page? I have no problem updating the firmware with the jar tool, but if I make any changes via the webpage interface the constant reboots occur. Also, if I make the needed changes to the config.json file, everything works fine (even after rebooting) unless I make changes in the web interface. It seems that whatever data is being written as a result of the webpage change is not passing correctly to the eeprom.
EE351 wrote:Does the jar tool use a different flash mode vs the web configuration page? I have no problem updating the firmware with the jar tool, but if I make any changes via the webpage interface the constant reboots occur. Also, if I make the needed changes to the config.json file, everything works fine (even after rebooting) unless I make changes in the web interface. It seems that whatever data is being written as a result of the webpage change is not passing correctly to the eeprom.
It does it if you just reboot the module as well without changing anything doesn't it? Sounds like something wonky going on in flash or with the way flash is mapped. Configuration File Format Error tells me it's being found in SPIFFS, however its corrupted. After programming, the module does a soft-reset so booting cold / resetting is a little different. Can you compare the flash chip to the ones on your working modules?
EDIT: Just saw the other post about its now rebooting fine. Can you post your config.json (without SSID and passphrase of course), and what parameters you're changing?
EE351 wrote:The modules I'm having trouble with are some new esp-01 I recently purchased.
So the ESP-12 with ESP-01 firmware works fine with flashing, configuration from the webpage and OTA updates, but just the ESP-01 you have are giving you problems?

