ESPixelStick - E1.3...
 
Notifications
Clear all

ESPixelStick - E1.31 WiFi Pixel Controller

948 Posts
178 Users
0 Reactions
503.7 K Views
Posts: 313
(@ee351)
Reputable Member
Joined: 13 years ago
pakeonoahu wrote:So the ESP-12 with ESP-01 firmware works fine with flashing, configuration from the webpage and OTA updates, but just the ESP-01 you have are giving you problems?

This is correct, the esp-01 jar flash tool works fine with my esp-12 modules without any changes to the code.


Reply
Posts: 313
(@ee351)
Reputable Member
Joined: 13 years ago
sporadic wrote:It does it if you just reboot the module as well without changing anything doesn't it? Sounds like something wonky going on in flash or with the way flash is mapped. Configuration File Format Error tells me it's being found in SPIFFS, however its corrupted. After programming, the module does a soft-reset so booting cold / resetting is a little different. Can you compare the flash chip to the ones on your working modules?

EDIT: Just saw the other post about its now rebooting fine. Can you post your config.json (without SSID and passphrase of course), and what parameters you're changing?

Here it is. I had to change the file extension to txt so it would upload. The only variables I changed are universe, channel_count, and multicast.


Reply
Posts: 313
(@ee351)
Reputable Member
Joined: 13 years ago
sporadic wrote:It does it if you just reboot the module as well without changing anything doesn't it? Sounds like something wonky going on in flash or with the way flash is mapped. Configuration File Format Error tells me it's being found in SPIFFS, however its corrupted. After programming, the module does a soft-reset so booting cold / resetting is a little different. Can you compare the flash chip to the ones on your working modules?

EDIT: Just saw the other post about its now rebooting fine. Can you post your config.json (without SSID and passphrase of course), and what parameters you're changing?

Here's a couple of pictures of the eeprom from the working and the problem esp-01 board.

eeprom ok
eeprom problem

Reply
Posts: 25
(@apexlights)
Eminent Member
Joined: 15 years ago

Can anyone help me figure out how to program a ESPixelstick pop? I have a FTDI.


Reply
sporadic
Posts: 1199
Topic starter
(@sporadic)
Noble Member
Joined: 14 years ago
EE351 wrote:Here's a couple of pictures of the eeprom from the working and the problem esp-01 board.

I've scoured around trying to find the specs for the SPI flash on the one you're having issues with. Puya Semiconductor doesn't even list a P25Q80. From the naming convention however, one would think it's a QIO 8Mbit chip, which usually supports DIO as well (same as one on your working board). The module looks a little sketchy however and seems to be an AI-Thinker copy. Their name is misspelled and the antenna traces are much fatter than usual which may adversely affect RF performance.


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

This thread is for shelby's espixel product, you need to post this question on the Bill Porter thread.
Find it here:
http://doityourselfchristmas.com/forums/showthread.php?47269-Espixel-by-Bill-Porter&highlight=espixel

apexlights wrote:Can anyone help me figure out how to program a ESPixelstick pop? I have a FTDI.

Reply
Posts: 1
(@natedog3018)
New Member
Joined: 12 years ago

I have a problem that a quick review of this thread did nto show. I just got the ESPixel from Amazon and was playing with it to decide if they would work for me. I finished assembly, plugged it up and fired up the downloader that was with the firmware. I successfully installed the firmware and find the board at 192.168.1.125. configured for 4 2811 pixels that i wired on and refreshed. my LOR sends the commands to the board and the pixels light red when commanded. Feeling good, i reboot the board and disconnect the USB programming cable.

Now I cant find the board, it no longer shows up on the routers attached devices where it was (192.168.1.125) and i see a ESP device at 192.168.1.102 with a different MAC address (not this is the only ESP on the network. hookit back up, flash again and the board is back at 192.168.1.125. Set it for static 19 at 192.168.1.125 and the board disappears. IF i use a browser to the addy, it refuses the connection on :80. if I put it back to dhcp and use the address the router shows it having, it refuses the connection.

Thinking a firmware issue, I move to the 3.0 RC. Use the jar utility and successfully flash it. This has a test mode and again, only red responds. no other colors. . Set a static IP and no response. leave the DHCP addy and as soon as it reboots, I cant access it and the mac address changes. I am at my wit's end.

It appears that it will not hold the IP addresses. It also does not appear to fall back to AP Mode as I never find the AP, so it must be on the network. Help-Does anyone have a suggestion or has anyone seen this behavior before?


Reply
Posts: 1387
 kev
(@kev)
Noble Member
Joined: 12 years ago
sporadic wrote:I'll replace it. Would like to do some analysis on it though to see what the issue is as it's a first. PM me your address and I'll get one out to you tomorrow.

Sent from my R1 HD using Tapatalk

Have you had a chance to test it yet? Just curious. Suspect a bad solder joint on one of the SMDs.


Reply
Posts: 1387
 kev
(@kev)
Noble Member
Joined: 12 years ago

Tested my WIFI range today by taking an ESPixelstick for a walk around the culdesac. I am using an ESPixelstick powered by two 9 volt batteries (in parallel) with 4 pixels attached as a portable test bed. I am using my Ipad as the portable terminal.
The WIFI signal strength standing close to the router location is about -47db. The signal strength at all of the locations around the yard where I expect to have the ESPixelsticks ranged from -74db to -77db. A walk across the culdesac showed a signal strength of -84db at a distance of approximately 110 feet.

IMG 3483
IMG 3571
IMG 3572

Reply
sporadic
Posts: 1199
Topic starter
(@sporadic)
Noble Member
Joined: 14 years ago
kev wrote:Have you had a chance to test it yet? Just curious. Suspect a bad solder joint on one of the SMDs.

Sorry, I haven't had a chance to get around to it yet. I do have it set aside though. Finally got around to getting my Halloween show going last night. Still working on some static props as well, lol. I'm always so behind for Halloween!


Reply
Page 77 / 95
Share: