ESPixelStick - E1.3...
 
Notifications
Clear all

ESPixelStick - E1.31 WiFi Pixel Controller

948 Posts
178 Users
0 Reactions
503.7 K Views
sporadic
Posts: 1199
Topic starter
(@sporadic)
Noble Member
Joined: 14 years ago
DrNeutron wrote:Just now getting around to loading firmware on my last batch of EXPIXELSTICKS and I have a problem with one.
No power to it at all. I tried swapping out the ESP module, checked fuse and reflowed all components but nothing.
I metered + and - and getting 4.97v in, across C1 I am getting 4.97v, but when I meter U3 I am getting nothing.

Sent you a PM.
thanks,
-shelby


Reply
DrNeutron
Posts: 2018
(@drneutron)
Noble Member
Joined: 14 years ago

Thanks Shelby, responded to your PM.


Reply
Posts: 17
 Code
(@code)
Active Member
Joined: 11 years ago

I have a problem with one of mine when programming, has anybody's came across this issue.

IMG 1357

I have changed the wifi part and no luck.

Sent from my iPhone using Tapatalk


Reply
Barnabybear
Posts: 1583
(@barnabybear)
Noble Member
Joined: 15 years ago
Code wrote:I have a problem with one of mine when programming, has anybody's came across this issue.

IMG 1357

I have changed the wifi part and no luck.

Sent from my iPhone using Tapatalk

Hi, some things that would give that result:

Not connecting Ground.

Tx & Rx the wrong way round (swapped).

Not pressing programing buttons in order; Apply power, press & hold RESET, press & hold PROG, release RESET, release PROG, then run flasher as normal.

If all of the above are correct you'll need to measure some voltages.

Hope that helps.


Reply
Posts: 2048
(@scootchu)
Noble Member
Joined: 17 years ago

Is it a black ESP-01 module? The black ones usually have 1M of memory on them, but there are green ones that have 512K. The green ones are older and the firmware won't fit. Otherwise Barnabybear's suggestions would be the one's I would follow. You should get a blue flash from the LED when you release reset while holding PGM. I guess you could just have a bad ESP-01 module.


Reply
sporadic
Posts: 1199
Topic starter
(@sporadic)
Noble Member
Joined: 14 years ago
Code wrote:I have a problem with one of mine when programming, has anybody's came across this issue.

IMG 1357

I have changed the wifi part and no luck.

Sent from my iPhone using Tapatalk

Can you swap the ESP-01 module to another board and verify if the issue follows the board or the module?
thanks,
-shelby


Reply
Posts: 17
 Code
(@code)
Active Member
Joined: 11 years ago

I changed the ESP-01 module as i have a few spare, Didn't work. So i created another espixekstick and put the ESP-01 on that and programmed it and then added it back to the faulty Stick and so far so good it works. lets me save the configuration etc. Unsure what the issue is but at least its working now


Reply
sporadic
Posts: 1199
Topic starter
(@sporadic)
Noble Member
Joined: 14 years ago
Code wrote:I changed the ESP-01 module as i have a few spare, Didn't work. So i created another espixekstick and put the ESP-01 on that and programmed it and then added it back to the faulty Stick and so far so good it works. lets me save the configuration etc. Unsure what the issue is but at least its working now

Let me know if you have anymore issues with it. Here are some voltage test points as well.

ESPixelStick V2 Voltage Testing by smerrick, on Flickr


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

Would not run at all if the voltage was off. Really sounds like the program or reset button are not making it to the ESP-01


Reply
Posts: 2048
(@scootchu)
Noble Member
Joined: 17 years ago

If it passes data to the pixels I would not worry about it. Sure it may not be perfect, but it will be functional.

Sent from my SM-G930V using Tapatalk


Reply
Page 68 / 95
Share: