ESPixelStick - E1.3...
 
Notifications
Clear all

ESPixelStick - E1.31 WiFi Pixel Controller

948 Posts
178 Users
0 Reactions
503.2 K Views
Posts: 413
(@gizmohd)
Honorable Member
Joined: 17 years ago

I'm having issues with my display this year... it appears at least two of my ESPixelSticks stop responding and fall of the network. Which in turn causes my fpp to drag to a slow and miserable halt over time.

I've attempted to rebuke it out by swapping the esp01 modules with new ones but still get the issue.

I'd almost like to see an option where as if no activity on the device was seen (web or e131) after n number of seconds it would reboot itself... since that's the only way I can get the devices to respond when it falls off

Sent from my iPhone using Tapatalk


Reply
sporadic
Posts: 1199
Topic starter
(@sporadic)
Noble Member
Joined: 14 years ago

I've been away for work and travel, just getting back to catching up on posts. Hoping to get my show rolling this week as well!

Kev7274 wrote:Thanks Jon.
I thought that it would display an ip address or something?

From the install manual...

Once the upload is complete, the ESPixelStick will relay is configuration status to the Serial Output window. You can now
connect to the ESPixelStick with your web browser for further configuration if required. It’s a good idea to record the IP
Address
as chances are, you’ll need it!

I've had a few users report that they don't receive proper output in the serial terminal, not sure what's going on yet. You can try connecting to it with a terminal emulator, like PuTTY at 115,200 and see if there's output when you reset the module.

gizmohd wrote:I'm having issues with my display this year... it appears at least two of my ESPixelSticks stop responding and fall of the network. Which in turn causes my fpp to drag to a slow and miserable halt over time.

I've attempted to rebuke it out by swapping the esp01 modules with new ones but still get the issue.

I'd almost like to see an option where as if no activity on the device was seen (web or e131) after n number of seconds it would reboot itself... since that's the only way I can get the devices to respond when it falls off

Sent from my iPhone using Tapatalk

When they drop off, are they disassociating from the AP or do they just stop responding? If still associated, can you ping them? Also, what's the average RSSI on the modules when working?


Reply
sporadic
Posts: 1199
Topic starter
(@sporadic)
Noble Member
Joined: 14 years ago
DMJPixel wrote:I know its not the best time for questions as everyone is busy doing their shows but hopefully these are easy to answer.

1) For the power connector you mention above, I know you say they are not weatherproof but I think it's implied you use them outdoors. If yes, do you cover the entire connection in liquid tape and then just slice it open if/when you need to remove OR do you cover each side but leave the joint where you can take it apart? I am curious if I can use this out in the weather. I was thinking another way to do this would be a 2nd 3 wire pigtail to feed power in (only use 2 wires).

2) I am struggling a bit with this next issue and am probably over-complicating it...I have a bridge by the road at the start of our driveway with a power outlet nearby. I plan on using one ESPixelStick on each side of the bridge to run the following, 40 brilliant bulbs, 16 rectangle nodes in candy cane, 48 pixel snowflake, another 48 pixel snowflake and a string of 100 nodes along a fence. I know the stick can handle the number of pixels but I am struggling with how to inject power in this setup but keeping the data line continuous. In other injection schemes I have read about (with a wired controller) it seems the data usually stops at the second injection point (megatree for example) but in this case I need to keep the data going through multiple "strings". I thought about making a Y-cable and maybe encasing it in a small PVC tube much like the holder for the stick itself. And if I did this would I clip the v+ at the injection point so it didn't extend power both directions thus keeping proper amps for each "section" if a fuse blew? I plan on using one power supply with a power distribution board (5 amp fuses on each leg) and possibly 3 power injection feeds. Any thoughts on how to do this; 3 wire pigtails, 4 wire, the XT-60 mentioned above?

Thanks in advance for any thoughts.
Dave

1) Just heatshrink and liquid tape on the backsides. I put a little dielectric grease in the mating ends. Also, the most my connectors see is some rain. They don't lay in any puddles and we rarely ever get snow down here.

2) I run so many modules in my show that I don't do any power injection, but it sounds like you're going down the right track. You can continue the data line along as its a common ground and inject power as needed.


Reply
Posts: 171
(@dmjpixel)
Estimable Member
Joined: 11 years ago
sporadic wrote:1) Just heatshrink and liquid tape on the backsides. I put a little dielectric grease in the mating ends. Also, the most my connectors see is some rain. They don't lay in any puddles and we rarely ever get snow down here.

2) I run so many modules in my show that I don't do any power injection, but it sounds like you're going down the right track. You can continue the data line along as its a common ground and inject power as needed.

Thanks for the info - appreciate the feedback!
Dave


Reply
michaelc
Posts: 1540
(@michaelc)
Noble Member
Joined: 19 years ago

This may be an off the wall question but does anyone have the part number for the 3amp fuse used in these modules. I just popped two due to bad downstream wiring. I see lots of 3 amp auto style fuses on Amazon but I'm not sure of the right size/voltage of these.

Also, I see these plugs are wired for 4 conductor pixels. Do the ESPIXELstrips support 4wire WS2801 pixels?


Reply
Page 64 / 190
Share: