I have 3 large trees that have single color LED strands in them in a superstring configuration. I have some RGB elements scattered around the yard so that a whole house effect looks halfway decent. For years. I've wrapped the trunks of the trees in LED rope lights and tied them into the tree tops. All Green, All Red, All Blue, All White. This year I got some of the pixel mounting strips and I'm creating 4 columns of 9 pixels (36 pixels) to help fill in some of the whole house pixel effects. I'm using the strap to make a custom 'net' that I can simply wrap around the tree and zip tie. These will each be run by an ESPixelstick. I was thinking of using these little DC modules to power each tree so I don't have long runs of 12V SPT2 and the associated voltage drops and I don't have to waste a power supply for each tree.
@ Martin. Ref the TP-LINK model TL-WA7210N.
Thank for that explanation it’s interesting to an indication of somethings potential even if you then have to consider a multitude of other factors. A lot of the stuff in this hobby is just really outside people’s knowledge base and it’s nice to get a bit of insight. From that; I takeaway reassurance that even with my repurposed older kit I should be good for the thousand pixels I’m intending to run over e1.31 WiFi.
The TL-WA7210N is on offer in the UK so I had a look at some of the reviews and whilst most people were 4 or 5 stars happy, there were a couple of comments I noted:
I was stated that it only has a 10/100 Ethernet connection (input), that down rates it by about a 1/3 on their spec and the potential you kindly quoted.
It was also stated that it is quite directional and a lot of the good comments were A to B connections over distance.
I don’t have one, but based on the comments about it being directional I’d be interested to here from anyone who has one and it’s suitability for our hobby & sorry this is off track – maybe a new thread is needed.
michaelc wrote:I'm doing some math. According to the specs, these little units put out 1-2Amps of 12V. Assuming I run all my pixels at 50% brightness and a typical pixel (2811) uses .06A. Is my math correct that I can run between 33 and 66 pixels from this. My thought is to run line voltage 120V AC to one of these guys sitting in a 1.25" pvc pipe to an ESPixelStick in the same pipe to drive up to 50 pixels. Is my math correct? And would this being so close to the ESPixel stick cause interference?
https://www.amazon.com/gp/product/B01JFL3FDS/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1
I'd measure the current draw on your pixels while full white, I've found many draw less than the specs would make you think. I ran across the below video on YouTube, but not sure what converter he used. I'd grab one and try it out. Success with distance really depends on how clean the power is. The on board supply cascades and has some filtering so you should be good. As for an AP, I like my Nanostation locoM2.
Sent from my XT1094 using Tapatalk
I think that's where I got the idea. Just not sure my little 1-2 amp board is powerful enough.
sporadic wrote:I'd measure the current draw on your pixels while full white, I've found many draw less than the specs would make you think. I ran across the below video on YouTube, but not sure what converter he used. I'd grab one and try it out. Success with distance really depends on how clean the power is. The on board supply cascades and has some filtering so you should be good. As for an AP, I like my Nanostation locoM2.Sent from my XT1094 using Tapatalk
LOL those are my wifi arches. The power converter was from Alibaba, it's a YS-12s-b 110AC to 5vdc. I think it was 2amp. And i tested them approx 125' from my wireless router that was in my garage. Works just fine.

