ESPixelStick - E1.3...
 
Notifications
Clear all

ESPixelStick - E1.31 WiFi Pixel Controller

948 Posts
178 Users
0 Reactions
503.2 K Views
Posts: 64
(@oceanwanderlust)
Trusted Member
Joined: 13 years ago
DMJPixel wrote:I am fairly new with xLights but willing to try and help. You should be able to setup the stick as an E1.31 controller - under the Setup tab click the ADD E1.31 button - I added a 4 universe stick as 192.168.69.73 - see pic below. Can you explain your issue a little further?

Your pic got my brain working again, thankyou... I only have one universe and need to add 3 more. I got confused and distracted when my single universe of 512 CHANNELS got divided by 3 for 170 PIXELS.


Reply
MartinMueller2003
Posts: 7613
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

To deliver 150Mbits to your router, you need an interface that is running faster than a 10/100Mbps interface. The next step up is gigabit. As for 2M Pixels, Updating once per second means you are not trying to sync to music or generate any type of smooth motion. I have found that for smooth motion you need at least 20fps. Anything less and the motion of the effects looks jerky to me.

You are correct, Raspberry PI cannot support gigabit (a PI cannot fill a 100Mbps pipe due to the interface between the Ethernet mac and the CPU). You did not ask about the creation of the data stream. You asked what the router could support. Those calculations are for a perfect router under perfect conditions. I suspect an el-cheapo router would not get to more than 25% of those numbers in a real world environment.

The number of stations a router can support is yet another separate specification that I cannot resolve for you. Math is straightforward real world operation is very tricky.


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

Thank you Martin. Your perfect world example does get us a ball park. I don't think any of us are getting close to those kind of pixel numbers. So the architecture is sound for us, we just need the right parts and setup.


Reply
michaelc
Posts: 1540
(@michaelc)
Noble Member
Joined: 19 years ago

I'm doing some math. According to the specs, these little units put out 1-2Amps of 12V. Assuming I run all my pixels at 50% brightness and a typical pixel (2811) uses .06A. Is my math correct that I can run between 33 and 66 pixels from this. My thought is to run line voltage 120V AC to one of these guys sitting in a 1.25" pvc pipe to an ESPixelStick in the same pipe to drive up to 50 pixels. Is my math correct? And would this being so close to the ESPixel stick cause interference?
https://www.amazon.com/gp/product/B01JFL3FDS/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1


Reply
Barnabybear
Posts: 1583
(@barnabybear)
Noble Member
Joined: 15 years ago

Hi, a cunning plan and whilst it will work I personally wouldn’t go for more than 30 pixels if you need reliability. At the bottom of the specs it states “Output Current: 1A-2A ; Output Power: 12W”. So 12W @ 12V = 1A, there saying it will do 2A but possibly in short bursts. Your maths with regard to the pixels was correct but you’ll need to allow about 100mA @ 12V (250mA @ 5V) for the pixelstick as well to be on the safe side.
So 1A – 100mA = 900mA divide that by your pixels @ 30mA and you get 30 pixels. Of cause with planning, only using single colours or not having all the pixels on at the same time you could get more.
What is the plan? We may be able to help.


Reply
Page 48 / 190
Share: