Super Strip Flood C...
 
Notifications
Clear all

Super Strip Flood Controller

240 Posts
30 Users
0 Reactions
91.6 K Views
Posts: 1041
(@n1ist)
Noble Member
Joined: 19 years ago

Those caps are a little big; the board is layed out for 0.25" (6.3mm) diameter ones.

100uF/35V: UVR1V101MED1TA or ECA-1VM101B should be fine, and you usually derate alumunum lytics to 70% of rated voltage.
330uF/10V: ECA-1AM331 would work. If you go with the smaller 100uF, ECA-1EM331B (330uF/25V) would fit.

Otherwise, you could just load one cap on either side of the board...

If you want to use a 0-ohm resistor instead of a piece of wire, CR0603-J/-000ELF
would be a good one.
For the header, 929834 is a straight one. 929835-01-03-RK is the RA one.

/mike


Reply
Posts: 1041
(@n1ist)
Noble Member
Joined: 19 years ago

I just discovered that the footprint I used for the diode had the opposite polarity from the schematic symbol. If you have already ordered boards, note that the silkscreen will be backwards. If not, here's an updated set of Gerbers.
/mike


Reply
budude
Posts: 10400
Topic starter
(@budude)
Illustrious Member
Joined: 18 years ago
n1ist wrote:Those caps are a little big; the board is layed out for 0.25" (6.3mm) diameter ones.

100uF/35V: UVR1V101MED1TA or ECA-1VM101B should be fine, and you usually derate alumunum lytics to 70% of rated voltage.
330uF/10V: ECA-1AM331 would work. If you go with the smaller 100uF, ECA-1EM331B (330uF/25V) would fit.

Otherwise, you could just load one cap on either side of the board...

If you want to use a 0-ohm resistor instead of a piece of wire, CR0603-J/-000ELF
would be a good one.
For the header, 929834 is a straight one. 929835-01-03-RK is the RA one.

/mike

OK - sounds good - must have cut/paste the wrong thing for the header - oops... here is the updated BOM:

517-929835-01-03-RK - 3-pin RA Header
652-CR0603-J/-000ELF - 0 ohm resistor
667-ECA-1AM331 - 330uF/10v (output)
667-ECA-1VM101B - 100uF/35v (input)
595-TL2575-05IKTTR - LM2575-5
704-DR127-331-R - 330uH inductor
833-MBRX140-TP - Diode

Total is $4.63/1, $4.18/25 and $3.84/50 (excluding shipping) - just need to find the cheapest way to get boards made now. It would be nice to hit $6 or less total but that might be tough...

Has anyone tried PCB-POOL for boards? They have a place right here in San Jose! I put in 1.0"x0.5" dimensions into their calculator and excluded the silkscreen and solder mask (yes - I know those are very nice to have but...) and could get 32 boards for $61.40 ($1.92 each) - but shipping was $45!!! say what?!?! I'm hoping since they are local to me that there might be a chance I could simply pick them up myself and save that cost or at least reduce it.

edit - forgot to mention that PCB-POOL provides a free stainless-steel stencil for the SMD soldering.


Reply
Posts: 1041
(@n1ist)
Noble Member
Joined: 19 years ago

I recently did a board with PCBGeek; they offer a proto service of 200 square inches for $89 shipped with mask and silk on both sides. That would give about 280 boards. That was the best price I found. That works out to around 32 cents a board.

/mike
.


Reply
budude
Posts: 10400
Topic starter
(@budude)
Illustrious Member
Joined: 18 years ago

Thanks for that Mike - I'll give them a look-see.

Back to the Ren48LSD, I finally got around to building out what will be the regulator circuit for it on a breadboard using the parts I plan to spec out. To put a solid load on it, I put a big 8.3 ohm load (actually two 25W resistors in series) across the output which equates to a 602mA load on the regulator. The normal full-on load for the LSD is just under 400mA (right around 385mA) so this is a signficant increase. I started with 12v and after 15 minutes or so the LM2575 was sitting at 43 degC - warm but you could hold on to it and not burn yourself. I then went to 24v and even 30v (the maximum output of my bench supply) and it stayed at right around 43-44 degC. Keeping in mind that the load is well over the worst case, it's clear this is going to work great! I'll probably keep the existing heat sink just to help keep the regulator a bit cooler anyway - it can't hurt it anyway...

I've got the new board mostly laid out - just need to see about those mounting holes once I compare to the CG1000 mechanical drawing I have for some guidance (or barring that, my calipers...).

So - this is your last call if you want something else (minor) added to the LSD - I'll probably send out for protos next week in order to kick off the coop planned for next month. I was thinking once again about disconnecting pin 7 from the outputs so that SSRs can be safely plugged in with straight Cat5 cables. I might add a small set of pads so that you can put in a jumper if you need the additional source pin for something. I'm updating the entire silkscreen to make it easier to locate specific parts instead of something like "the tenth one over from the right"... oh - and it will be tinned this time too. :p


Reply
Page 36 / 48
Share: