Here are the gerbers; I haven't built this either; I just tossed it together to try out the layout. I'll be including it in my next BatchPCB order, but that will take 2-3 weeks before it shows up. I use Kicad; not sure if the component libraries would help, but I can upload them if they would.
/mike
Has this been breadboarded? Is that possible?
n1ist wrote:Here are the gerbers; I haven't built this either; I just tossed it together to try out the layout. I'll be including it in my next BatchPCB order, but that will take 2-3 weeks before it shows up. I use Kicad; not sure if the component libraries would help, but I can upload them if they would./mike
n1ist wrote:Here are the gerbers; I haven't built this either; I just tossed it together to try out the layout. I'll be including it in my next BatchPCB order, but that will take 2-3 weeks before it shows up. I use Kicad; not sure if the component libraries would help, but I can upload them if they would./mike
Can you suggest a BOM as well - I started looking but unfortunately, I'm not 100% sure what your component packages are for the resistors or diodes...
I attempted one on Newark and came up with:
http://www.newark.com/coiltronics/dr127-331-r/power-inductor-330uh-1-04a-20/dp/52K7537 - DR127-331-R - $1.84
http://www.newark.com/national-semiconductor/lm2575s-5-0-nopb/ic-step-down-regulator-to-263-5/dp/41K3660 - LM2575S-5.0/NOPB - $2.78
http://www.newark.com/vishay/ss2h9/diode-schottky-2a-90v/dp/34M8641 - SS2H9 - $0.39
http://www.newark.com/multicomp/mcre000086/resistor-0201-1-0r/dp/10R8750 - MCRE000086 - $.007
http://www.newark.com/illinois-capacitor/107ckr050m/capacitor-alum-elect-100uf-50v/dp/69K7856 - 107CKR050M - $0.076
http://www.newark.com/illinois-capacitor/337cks025m/capacitor-alum-elect-330uf-25v/dp/69K7877 - 337CKS025M - $0.086
or about $5.20 in parts (single qty)...
The resistors are 0603 (and for a fixed regulator, you can get away with a little scrap of wire jumpering R2. The diode is in a SOD123 package; Mouser 771-PMEG4010EH-T/R or 833-MBRX140-TP should work. The rest of those look good to me.
/mike
OK - I built out a Mouser BOM this time:
140-REA331M1EBK1012P 330uF/25v Cap
140-REA101M1HBK0811P 100uF/50v Cap
595-TL2575-05IKTTR LM2575-5 fixed
704-DR127-331-R 330uH/1A coil/inductor
833-MBRX140-TP Diode
517-834-01-03 3-pin right angle header (almost forgot that...)
All told - $4.76 in parts - not bad at all... I know we can get away with a 16v output cap but I figured if folks want a 15v regulator, the 25v would be safer - either fit anway... If you want to use an adjustable regulator, then this BOM needs modification - once the 5v version is shown to be working, a list of optional parts can be provided but I think by far the 5v version (maybe the 3.3v version as well) will be the most popular.
Mike - if you don't mind - please bless these and we'll go from there!
