Does the PCB layout shown below look like it would work okay in terms of component layout, and being able to be fabricated by a PCB house? I used ExpressPCB to draw this. I have never had a PCB made, so I don't know what works or doesn't in terms of size of holes or how close they can be to the edge, etc. I guess I'm more concerned about the layout of parts, traces and holes, and not so much about the silk screen layer at this time (since I haven't labelled parts yet), although tips in that area would also be welcome.
I am wanting to make a single-sided board, so that maybe it could be home etched if I ever try that. I would also like to use this board as-is, or be able to cut it up into 8 sections that could be used individually, so I left a little clearance between each copy (but I didn't know how much space I should actually leave). I read over David Jones' excellent PCB design tutorial, and it was helpful but it seems to be more oriented towards "normal" boards (not the 1-sided, 8-up thing I'm trying to do).
I am also wanting to accomodate 14-pin or 20-pin PICs, so I put them in the same place and will use jumpers to connect the varying pins to their traces. The red lines show all the possible jumpers, but only half of them would be used for any given configuration (or less if ZC or ext clock were not needed). I bent a couple of the jumpers only so they did not hide the trace from view (they would be straight in actual practice). There are also a couple of jumpers that are there in lieu of a second side, so those ones are not optional.
For the ZC and power areas at the bottom, I really didn't know how to handle that in the smallest possible space, so I would be interested in any suggestions on that area also. I want to be able to use it several different ways:
- 120 VAC connected at bottom left to drive a regular H11AA1-based ZC circuit, with 5 VDC connected separately at bottom right
- ~ 12 VAC connected at the bottom left to supply ZC and if a diode bridge is populated then it can also be used to supply the regulator and caps in the bottom right
- connect either a filtered 5 VDC supply to the bottom right and bypass the regulator and caps, or an unfiltered 5 - 12 VDC supply and then use the regulator and caps to turn it into a filtered power supply on-board
- accomodate a half-size or full-size ext clock near the center in the bottom right (again just the standard Renard circuit)
thanks
don
I don't have to much to add at the moment, other than you may have difficulties because of the lack of a ground connection on the RJ45 connectors, and that the cap on the input to the regulator might want to be exchanged with the cap that you now have on the output of the regulator. Also, you want to allow for physically larger resistors on the H11AA1 input, and you probably want to turn the input diodes around.
Don - I don't believe jumper headers/shunts will fit in the "default" hole size of .056/029 - I'm not sure of the best size myself - perhaps someone can chime in here? I know MTA100 connecters don't fit and I think they are the same pin size - I had to drill out my pretty new boards to make them go in... I'm guessing a .075/.040 would be OK...
An 0.025 square post has a diagonal of 0.0354. Amp recommends a 0.040 hole for their mates for the MTA100; I would use the same for a 2-pin "snap off" jumper. The 3M 2500 series wants a 0.035 hole, so I'm guessing the tails are a reduced size there.
/mike
Thank you for the info about hole sizes. That is very helpful.
Is there some kind of reference chart somewhere about which sizes to use for various types of parts or leads? I often see physical dimensions on spec sheets, but that doesn't really tell me how much "extra" clearance to leave.
P. Short wrote:you may have difficulties because of the lack of a ground connection on the RJ45 connectors
If I am charlie- or chipi-plexing the SSRs so that one of the I/O lines would be acting as ground, would a true ground still be needed for other purposes such as to reduce interference or to balance the twisted pairs?
P. Short wrote:the cap on the input to the regulator might want to be exchanged with the cap that you now have on the output of the regulator
Is that due to their sizes/shapes, or that the actual layout order with respect to direction of current flow is important?
P. Short wrote:allow for physically larger resistors on the H11AA1 input
Is it safe/acceptable to turn these resistors "on end" to take less space, or should they always be parallel to the board surface?
thanks
don
