Super Strip Flood C...
 
Notifications
Clear all

Super Strip Flood Controller

240 Posts
30 Users
0 Reactions
91.6 K Views
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

Funny you should say this.
I already got the parts to build one of these but have been busy with another project. Cool.

budude wrote:Yep - using the 5v fixed version - keep in mind the BOM will be updated with the proper part numbers so hopefully it will be clear which one to get.

I am also looking at creating a module using SM parts as a drop-in replacement for the 7805. I realize these already exist but I'm a tad worried that they aren't available from the larger distribution places like Mouser, Digi-Key, etc. Of course that doesn't mean they will have parts available all the time either (in fact the SM version of the 2575 was OOS at Mouser and I had to go with Digi-Key) but if we get enough interest it might be cheaper than buying them separately - just have to work out the numbers.

I think this module would work for other applications like the Ren24LV as well.


Reply
budude
Posts: 10400
Topic starter
(@budude)
Illustrious Member
Joined: 18 years ago

I need to actually breadboard the circuit with the parts I have on hand to be sure it all works good, but I've laid out a pretty small 1"x.5" board that will hold the LM2575, coil and diode. All parts are SMT but very easy to build (at least it looks like it). It should be a drop-in replacement for an LM7805 for both the Ren48LSD (v3b) and probably the Ren24LV so that the big honking resistor will no longer be necessary. The overall cost would probably be slightly more than the existing module but at least there's more control over getting them.


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

Very nice.
I look forward to building one of these to test.

budude wrote:I need to actually breadboard the circuit with the parts I have on hand to be sure it all works good, but I've laid out a pretty small 1"x.5" board that will hold the LM2575, coil and diode. All parts are SMT but very easy to build (at least it looks like it). It should be a drop-in replacement for an LM7805 for both the Ren48LSD (v3b) and probably the Ren24LV so that the big honking resistor will no longer be necessary. The overall cost would probably be slightly more than the existing module but at least there's more control over getting them.

Reply
Posts: 1041
(@n1ist)
Noble Member
Joined: 19 years ago

I would prefer having the caps on board; you really do need to minimize the loop area, both for stability and EMI. Here's a layout that puts the caps on board. Even here, the input cap is a bit far away; up top would be better, but that would make the board taller. It's using a DR127-sized inductor from Coiltronics. It also has the resistor divider on board; that way tou could use the adjustable version if it's available or you need to trim voltages. For the fixed version, just load a 0-ohm resistor in the top side and leave the bottom side of the divider open.

/mike


Reply
budude
Posts: 10400
Topic starter
(@budude)
Illustrious Member
Joined: 18 years ago
n1ist wrote:I would prefer having the caps on board; you really do need to minimize the loop area, both for stability and EMI. Here's a layout that puts the caps on board. Even here, the input cap is a bit far away; up top would be better, but that would make the board taller. It's using a DR127-sized inductor from Coiltronics. It also has the resistor divider on board; that way tou could use the adjustable version if it's available or you need to trim voltages. For the fixed version, just load a 0-ohm resistor in the top side and leave the bottom side of the divider open.

/mike

Sweet - heck it won't hurt my feelings to go with yours! :p Would you mind providing Gerbers for this and I'll see about having some made up. I really need to update my component library some day too - it's good in some places but sucks in others...


Reply
Page 34 / 48
Share: