Super Strip Flood C...
 
Notifications
Clear all

Super Strip Flood Controller

240 Posts
30 Users
0 Reactions
91.6 K Views
Posts: 1041
(@n1ist)
Noble Member
Joined: 19 years ago

My regulator boards have arrived; I have loaded one and it is looking good. I used random caps that were on my bench, and I needed to add 100nF to the output to tame some ringing and switching noise. Good thing I have a footprint already on the board for that. At 1A load, the inductor starts getting hot, but still stayed around 50C. It was around 44C for 0.83A load, both with 24V in.

/mike


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

So I was going through some old postings on the LED Super Strips, looking for nuggets of assembly wisdom because I have the 2011 boards and 3 sets of the 2010 version of the LEDs and 2 sets of the 2011 version of the LEDs, and I came across this:

budude wrote:Well - I spec'd 1/8W resistors but all I had was 1/4W on hand so my fingers are sore trying to fit those suckers in! I can't say this is a lot of fun to build since you have to massage 48 transistors into the holes but then again I don't see having more than one or two these around anyway.

And the obvious question popped into my head, I wonder how many LSD board Brian actually did make???


Reply
budude
Posts: 10400
Topic starter
(@budude)
Illustrious Member
Joined: 18 years ago
dirknerkle wrote:So I was going through some old postings on the LED Super Strips, looking for nuggets of assembly wisdom because I have the 2011 boards and 3 sets of the 2010 version of the LEDs and 2 sets of the 2011 version of the LEDs, and I came across this:

And the obvious question popped into my head, I wonder how many LSD board Brian actually did make???

Well... I made only two of the v3a's which never saw daylight - I still have one, the other I gave to LabRat to do some testing. The rest of mine are all v3b's - I probably have 6 of these built - most are 5v - I think only two have the regulator which is the switching type replacement for the 7805. I have one v3c prototype (on a hideous "green" board!) but no other v3c's built - I do have a kit for one but will probably cannabilize for the PropLSD board... so now you know.

In case you're wondering - - v1x boards were ExpressPCB format (never built a board), v2x boards were PCBArtist format (never built a board) and all the v3x's are DipTrace format.

You should talk -- you must have about 50 types of controllers by now from the crazy lab of yours!


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
budude wrote:You should talk -- you must have about 50 types of controllers by now from the crazy lab of yours!

😆

Touche, mon ami!

Let's see... I admit to having just a few boards around DIGWDF... ummm...... there are 3 or 4 each of Ren8's, Ren8/16's and Ren8/16XB's, a WiRen, MiniRen8/4, MiniRen8, about a dozen MiniRen8/4XB's, half-dozen MiniRen8/8XB's, MiniRen8XBLSD (only 3 of those)... in addition to the standards: Ren64XC's, several SS24, SS16 and SS8's, a couple Ren24LV's, a couple Ren48LSDs (both a and b versions), an Ren16Xmus, a SimpleRen24 and SimpleRen32... and a couple Olsen595/Ren-C's for good measure in case the other stuff burns out...

...so I admit that I am guilty as charged... but I like to be "ready" for nearly anything...

Still, I couldn't help pondering whether you stopped at only two LSD's with all those little trannysitters... Somehow I just KNEW you couldn't... :mrgreen:


Reply
chelmuth
Posts: 1077
(@chelmuth)
Noble Member
Joined: 16 years ago

I made 8 LSD's and 48 SuperStrips, and 10 ss24's .. and hopefully soon a few more LSD's and 48 FAST Tubes..


Reply
Page 48 / 48
Share: