FPP PB16 Pixel Cont...
 
Notifications
Clear all

FPP PB16 Pixel Controller

630 Posts
62 Users
6 Reactions
389.3 K Views
Posts: 128
(@sctwohig)
Estimable Member
Joined: 10 years ago
scooter_seh wrote:I assume you want a BBB based board with two or three expansion port?

Pretty much the pb16 Expansion but with a Beagle bone black instead of a pocket beagle.

Thanks,
Shawn


Reply
Posts: 79
(@bobsmith)
Trusted Member
Joined: 11 years ago

Do you have an Arrow BOM in github somewhere? I see recently you said you migrated the BOM to Arrow. I actually finished ordering all my parts from Mouser / Amazon, and AliExpress. Mouser is about $80 cheaper than Digikey on the BOM for 5xPB16, 5xDiff Expansion, and 20x Diff Receivers for the parts I didn't get elsewhere. I figured I might as well build out all the PCBs I ordered, even though I really only have plans to run 2 controllers, and maybe 3 or 4 remote diff breakouts, but I have lots of room to grow now!

I skipped all the IC and resistor network sockets, got the fuseholders on amazon ($20 cheaper overall than buying the individual contacts without the black plastic base on digikey or mouser, which is WAY cheaper than buying the fuseholders with the black plastic base), and most of the connectors and fuses from AliExpress, though to be honest, the connector prices at AliExpress aren't that much different than mouser, except when you get to the 3.5mm 3pin connectors where the quantity is high. The difference adds up fast there. Also the pocketbeagles are considerably cheaper at Mouser ($35) than digikey ($45.60). Buy 5 of those, and that difference adds up fast!

My total cost per set (PB16 + diff expansion + 4 diff receivers) works out to $137.09, including everything but usb to ethernet adapters, sd cards, and generic switchmode dc-dc regulators from amazon, as the Murata ones in the BOM are sold out everywhere.

Looking forward to all the parts orders trickling in now, and soldering it all together hopefully sometime soon!


Reply
Posts: 87
Topic starter
(@scooter-seh)
Trusted Member
Joined: 12 years ago

If you send me the BOM with links I can added them to my BOM.

bobsmith wrote:Do you have an Arrow BOM in github somewhere? I see recently you said you migrated the BOM to Arrow. I actually finished ordering all my parts from Mouser / Amazon, and AliExpress. Mouser is about $80 cheaper than Digikey on the BOM for 5xPB16, 5xDiff Expansion, and 20x Diff Receivers for the parts I didn't get elsewhere. I figured I might as well build out all the PCBs I ordered, even though I really only have plans to run 2 controllers, and maybe 3 or 4 remote diff breakouts, but I have lots of room to grow now!

I skipped all the IC and resistor network sockets, got the fuseholders on amazon ($20 cheaper overall than buying the individual contacts without the black plastic base on digikey or mouser, which is WAY cheaper than buying the fuseholders with the black plastic base), and most of the connectors and fuses from AliExpress, though to be honest, the connector prices at AliExpress aren't that much different than mouser, except when you get to the 3.5mm 3pin connectors where the quantity is high. The difference adds up fast there. Also the pocketbeagles are considerably cheaper at Mouser ($35) than digikey ($45.60). Buy 5 of those, and that difference adds up fast!

My total cost per set (PB16 + diff expansion + 4 diff receivers) works out to $137.09, including everything but usb to ethernet adapters, sd cards, and generic switchmode dc-dc regulators from amazon, as the Murata ones in the BOM are sold out everywhere.

Looking forward to all the parts orders trickling in now, and soldering it all together hopefully sometime soon!


Reply
Posts: 1
(@arjang)
New Member
Joined: 7 years ago

I noticed you put a hole on the design to reach the S2 button, but i think you can also put a button on your board which connects to P8-43 and ground.

source:
https://github.com/victronenergy/venus/wiki/bbb-boot-process-overview

Holding down the S2 'boot' switch on the BBB when powering (or temporarily grounding P8.43) tells the ROM that the SD card (MMC0) should be the first boot device.


Reply
Posts: 629
(@dkulp)
Honorable Member
Joined: 14 years ago

As an FYI: if you purchase a BBB that was manufactured in the last 3 years, you don't need to ever press the S2 button. All recent beagles have the new boot loader on them and the s2 press is not needed. If you've installed any version of FPP from 3.x onto the eMMC, you also don't need to hold the S2 button as an updated bootloader would also be installed.


Reply
Page 78 / 126
Share: