FPP PB16 Pixel Cont...
 
Notifications
Clear all

FPP PB16 Pixel Controller

630 Posts
62 Users
6 Reactions
389.5 K Views
Posts: 186
(@steve123)
Estimable Member
Joined: 7 years ago

I noticed there is a BBB_16 board now that uses the BeagleBone Black instead of the Pocket Beagle. Has anyone done any testing with that board?


Reply
Posts: 116
(@jcasterline)
Estimable Member
Joined: 15 years ago
steve123 wrote:I noticed there is a BBB_16 board now that uses the BeagleBone Black instead of the Pocket Beagle. Has anyone done any testing with that board?

If there is a BBB board out there that needs testing, I volunteer. I've been playing around with a non-christmas pixel project. For this project, I'm currently using a raspberry pi & some serially connected arduino's.

Sent from my XT1254 using Tapatalk


Reply
Posts: 186
(@steve123)
Estimable Member
Joined: 7 years ago

There definitely is a BBB version. Unknown to me if it has been tested though. Scott said earlier in this thread he doesn't say much about new designs until he has had a chance to evaluate them.

Scott, if you see this, there is a long standing hardware bug with the BBB which has to do with the power up sequence. Sometimes, the ETH PHY does not sequence properly and therefore does not come out of reset properly. The consequence is occasionally the ETH does not come up when the board is powered up. It is an infrequent occurrence but nevertheless a problem for anyone that regularly cycles power to the board.

The problem can be fixed somewhat by using a GPIO to reset the ETH PHY. It is a bit of a complicated hack because of the location of the reset line ... the trace going to the ETH reset needs to be cut and a wire pasted to a GPIO. I do not know if there is a "commonly" used GPIO for this purpose and if it is coded into the current drivers. You might want to dig and determine if there is a "standard" so to speak, and avoid using that GPIO for anything else.

The proper solution for this problem is a hardware update to the BBB PMIC circuits to fix the sequencing problem but for whatever reason, the BBB has not been updated in the last than in 6 years. It is a good embedded computer ... in some ways superior to a RPi because it can be built to work across a wider temperature range. It also has some low power modes the Pi doesn't though that might not be true for the new Pi.

Unfortunately, the BBB receives very little love from TI, which is its original sponsor.


Reply
Posts: 87
Topic starter
(@scooter-seh)
Trusted Member
Joined: 12 years ago

I assembled a v1 version of the BBB controller and it worked. For the v2 revision I added push buttons and a header for an audio breakout board. I have not tested these additions. I have not created a EEPROM file for it but the pixel ports are are the same mapping as the F32-B so it can be used instead in FPP.

IMG 20200811 225632 (1)

steve123 wrote:There definitely is a BBB version. Unknown to me if it has been tested though. Scott said earlier in this thread he doesn't say much about new designs until he has had a chance to evaluate them.

Scott, if you see this, there is a long standing hardware bug with the BBB which has to do with the power up sequence. Sometimes, the ETH PHY does not sequence properly and therefore does not come out of reset properly. The consequence is occasionally the ETH does not come up when the board is powered up. It is an infrequent occurrence but nevertheless a problem for anyone that regularly cycles power to the board.

The problem can be fixed somewhat by using a GPIO to reset the ETH PHY. It is a bit of a complicated hack because of the location of the reset line ... the trace going to the ETH reset needs to be cut and a wire pasted to a GPIO. I do not know if there is a "commonly" used GPIO for this purpose and if it is coded into the current drivers. You might want to dig and determine if there is a "standard" so to speak, and avoid using that GPIO for anything else.

The proper solution for this problem is a hardware update to the BBB PMIC circuits to fix the sequencing problem but for whatever reason, the BBB has not been updated in the last than in 6 years. It is a good embedded computer ... in some ways superior to a RPi because it can be built to work across a wider temperature range. It also has some low power modes the Pi doesn't though that might not be true for the new Pi.

Unfortunately, the BBB receives very little love from TI, which is its original sponsor.

IMG 20200811 225632

Reply
Posts: 39
(@jleiwig)
Trusted Member
Joined: 17 years ago
scooter_seh wrote:I assembled a v1 version of the BBB controller and it worked. For the v2 revision I added push buttons and a header for an audio breakout board. I have not tested these additions. I have not created a EEPROM file for it but the pixel ports are are the same mapping as the F32-B so it can be used instead in FPP.

Wait...it can't be official. It's not blue! I thought they had to be blue?


Reply
Page 48 / 126
Share: