Another Simple Rena...
 
Notifications
Clear all

Another Simple Renard

84 Posts
21 Users
0 Reactions
34.2 K Views
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Member
Joined: 17 years ago

We will be sending an order to the PCB house this week for 10 Prototype Samples, if they work OK we will offer them to the DIYC community.


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

Looks neat, Mac!


Reply
Posts: 1041
(@n1ist)
Noble Member
Joined: 19 years ago

A few comments:
- The main AC traces (input connector to fuses) do not look wide enough for 14A, especially if you are using 1oz copper. I'd check all the high-current traces; a trace width chart can be found at http://www.armisteadtechnologies.com/trace.shtml
- Is the AC input connector rated for the current?
- The 7805 should have 100n ceramic caps on both sides (the data sheet actually recommends 330n on the input but I have used 100n with no problems) to prevent oscillations
- The ground plane is swiss-cheesed a bit; some of the back side traces can easily be moved topside (ie, ICSP1 to R11 can be topside if the trace from U9p4 is run between the leads of R11)
- There is silkscreen on exposed pads; when generating the Gerbers, there may be an option to subtract the soldermask from the silkscreen.
/mike


Reply
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Member
Joined: 17 years ago
n1ist wrote:A few comments:
- The main AC traces (input connector to fuses) do not look wide enough for 14A, especially if you are using 1oz copper. I'd check all the high-current traces; a trace width chart can be found at http://www.armisteadtechnologies.com/trace.shtml
- Is the AC input connector rated for the current?
- The 7805 should have 100n ceramic caps on both sides (the data sheet actually recommends 330n on the input but I have used 100n with no problems) to prevent oscillations
- The ground plane is swiss-cheesed a bit; some of the back side traces can easily be moved topside (ie, ICSP1 to R11 can be topside if the trace from U9p4 is run between the leads of R11)
- There is silkscreen on exposed pads; when generating the Gerbers, there may be an option to subtract the soldermask from the silkscreen.
/mike

Mike,

I made most of your suggested changes and the traces will be 2oz copper and each AC bank will handle 6 amps and the AC connector is rated at 13.5 amps,, changes noted in post #61

Thanks


Reply
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Member
Joined: 17 years ago

Here is a picture of a blank Simple Renard LCC 16,, should have one complete and tested soon then I will post some pictures.. they will be available at N7XG's site soon.
http://n7xgshop.net/shop/category.php?id_category=5

SR LCC 16

Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

Nice, clean board, Mac. Well done!


Reply
Posts: 3277
 Jrd
(@jrd)
Famed Member
Joined: 19 years ago

Looks good! 🙂


Reply
kychristmas
Posts: 3955
(@kychristmas)
Famed Member
Joined: 18 years ago

When will there be a BOM? or does it already exist somewhere?

Mactayl wrote:Here is a picture of a blank Simple Renard LCC 16,, should have one complete and tested soon then I will post some pictures.. they will be available at N7XG's site soon.
http://n7xgshop.net/shop/category.php?id_category=5

Reply
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Member
Joined: 17 years ago
kychristmas wrote:When will there be a BOM? or does it already exist somewhere?

Kelly,

There is a BOM and Mouser Project link but I am double checking it as I build the SR LCC 16 to make sure it is correct as soon as I verify it I will post it... later today or tomorrow morning..


Reply
kychristmas
Posts: 3955
(@kychristmas)
Famed Member
Joined: 18 years ago
Mactayl wrote:Kelly,

There is a BOM and Mouser Project link but I am double checking it as I build the SR LCC 16 to make sure it is correct as soon as I verify it I will post it... later today or tomorrow morning..

Thanks Mac. As always, amazing follow-through and support. If you can't tell, I'm very exicited about both the 16LCC and the Ren 8 🙂


Reply
Page 7 / 9
Share: