Another Simple Rena...
 
Notifications
Clear all

Another Simple Renard

84 Posts
21 Users
0 Reactions
34.2 K Views
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Member
Joined: 17 years ago

Hopefully I will have some results soon, just waiting on parts Ricky..:biggrin:


Reply
Posts: 3277
 Jrd
(@jrd)
Famed Member
Joined: 19 years ago

Ok, I love seeing new designs. 🙂


Reply
Posts: 255
(@frankv)
Reputable Member
Joined: 17 years ago

I really like the LCC idea... I currently have 2 REN24s... they only have 100-LED strings connected, so the LCC would be much more suitable.

One question... What would be needed to make this 230/240V compatible? I assume it would just be a matter of replacing the transformer?


Reply
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Member
Joined: 17 years ago
frankv wrote:I really like the LCC idea... I currently have 2 REN24s... they only have 100-LED strings connected, so the LCC would be much more suitable.

One question... What would be needed to make this 230/240V compatible? I assume it would just be a matter of replacing the transformer?

Since the transformer has a parallel primary and can be setup for 230 volt operation,, I will add traces for jumpers for 115/230 VAC operation,, not sure what else is needed for Down Under...:biggrin:


Reply
Posts: 3277
 Jrd
(@jrd)
Famed Member
Joined: 19 years ago
frankv wrote:I really like the LCC idea... I currently have 2 REN24s... they only have 100-LED strings connected, so the LCC would be much more suitable.

One question... What would be needed to make this 230/240V compatible? I assume it would just be a matter of replacing the transformer?

I haven't looked up the exact parts being used but I would think the PhotoTriacs and fuses would probably also need to be changed.

I wonder if the rectifier can handle 50hz AC as well as 60.


Reply
macebobo
Posts: 1595
Guest
(@macebobo)
Member
Joined: 17 years ago

Mac and Tyler,

Love it and can't wait to see it on Dean's store 😀

-- John


Reply
CaptKirk
Posts: 2200
(@captkirk)
Noble Member
Joined: 16 years ago

For the phototriac, will you be putting a dummy hole drilled in the board at the missing pin to accompodate a full 8 pin socket or is the expectation to solder it directly to the board, or cut the pin off the socket??


Reply
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Member
Joined: 17 years ago
CaptKirk wrote:For the phototriac, will you be putting a dummy hole drilled in the board at the missing pin to accompodate a full 8 pin socket or is the expectation to solder it directly to the board, or cut the pin off the socket??

CaptKirk,

I would rather have folks cut pin7 off of the IC socket if they use them only because it would give just a bit more isolation between pin6 and pin8 of the VO2223A or they could just pull pin7 out of the socket,, that is pretty much up to the end user..


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

It would be better to completely remove the pin from the socket since you lose the isolation between pins with an empty socket pin there. The non-machined sockets that we use here are pretty easy to pull a pin out from (I do this all the time for 8-pin to 6-pin conversions).


Reply
CaptKirk
Posts: 2200
(@captkirk)
Noble Member
Joined: 16 years ago

Makes sense!! Socket stripping it is!!


Reply
Page 6 / 9
Share: