Another Simple Rena...
 
Notifications
Clear all

Another Simple Renard

84 Posts
21 Users
0 Reactions
34.2 K Views
Posts: 225
 amps
(@amps)
Reputable Member
Joined: 15 years ago

Any idea what the rough cost to build one of these suckers may be? You've got my brain spinning trying to cram more lights into my display...


Reply
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Member
Joined: 17 years ago

Here is a quick picture of a completed SR LCC 16.. pricing is available at N7XG's site, I will also post a BOM tomorrow.
http://n7xgshop.net/shop/product.php?id_product=21

Thanks for you interest
Mac

SR LCC 16

Reply
crazy_carpenter
Posts: 369
(@crazy-carpenter)
Reputable Member
Joined: 15 years ago
Mactayl wrote:Here is a quick picture of a completed SR LCC 16.. pricing is available at N7XG's site, I will also post a BOM tomorrow.
http://n7xgshop.net/shop/product.php?id_product=21

Thanks for you interest
Mac

Shame on you guys. Now I have to explain to my wife why I'm ordering more boards and parts. :omg:


Reply
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Member
Joined: 17 years ago
crazy_carpenter wrote:Shame on you guys. Now I have to explain to my wife why I'm ordering more boards and parts. :omg:

:biggrin2::biggrin2::biggrin2:


Reply
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Member
Joined: 17 years ago

I have attached the BOM and Renard/DMX MPLAB project file which is setup for a PIC18F2525 start address 0 channels 1-16 which you can change to what ever you like along with DMX code if you select that, usable devices are PIC16F723, PIC16F722, PIC18F2420, PIC18F2525 and PIC18F2620,, (your choice). The BOM has a Mouser project link included, you can probably get the parts elsewhere a lot cheaper which is up to you.. Info will be added to the Wiki as time permits, thanks to Jack (jklingert)
I have also added a partial start address chart.

Thanks for your interest


Reply
crazy_carpenter
Posts: 369
(@crazy-carpenter)
Reputable Member
Joined: 15 years ago

Any hope for a GB on parts? I ran the Mouser BOM and it was like 65$


Reply
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Member
Joined: 17 years ago
crazy_carpenter wrote:Any hope for a GB on parts? I ran the Mouser BOM and it was like 65$

Not sure about a Group Buy at the moment,,, the way I did the BOM was it included all parts needed to build the PCB to its full build with all optional parts which makes the cost high. Some folks won't use all the sockets, jumper pins and even the terminal blocks and solder the AC wires right to the board. Mouser is quite high on their prices when you only buy a few parts at a time as this happens in any case for any board you build that is not done via a Group Buy. So we will see if we can get something going to reduce the cost.

Thanks for your interest..


Reply
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Member
Joined: 17 years ago

Hi All

I changed the MPLAB file in post 75 of this thread,, I needed to change the code for better linear incandescent dimming.


Reply
Posts: 46
(@davron12)
Trusted Member
Joined: 15 years ago

What happened to the on board transformer? It was mentioned a lot and I see Mac had added it, but then in post 72 it's gone. Just curious.


Reply
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Member
Joined: 17 years ago
davron12 wrote:What happened to the on board transformer? It was mentioned a lot and I see Mac had added it, but then in post 72 it's gone. Just curious.

That will be added next year.


Reply
Page 8 / 9
Share: