Activity
 
Notifications
Clear all
DynamoBen
@dynamoben
Famed Member
Joined: Jun 4, 2007
Topics: 165 / Replies: 2465
Reply
RE: Loving Falcon

Forgot to mention PocketVJ which has some cool features like video surface mapping and projector control which might be able to be "lifted" for Falcon...

10 years ago
Reply
RE: Loving Falcon

CaptainMurdoch wrote:I'm happy with the progress we've made in FPP over the past 3 years and even more excited as I look forward to a lot of the thing...

10 years ago
Reply
RE: Loving Falcon

Cmschleich wrote:I have to say, it is some of the more polished and easy to use free software I've tried of any function. Agreed. I spent many years...

10 years ago
Topic
10 years ago
Replies: 12
Views: 5567
Reply
RE: Enttec USB + 3ch Decoder = Random Blinking?

Vadoo wrote:On the far upper side of uncomfortably hot. If it's not the FTDI chip, and you didn't get a blister you might be OK if it's something li...

10 years ago
Forum
DMX
Reply
RE: sACN, e1.31, DMX, what does it all mean!?

Vadoo wrote:I get the impression a controller based e1.31 device is less likely to have compatibility issues then a software dependent slave device su...

10 years ago
Forum
DMX
Reply
RE: sACN, e1.31, DMX, what does it all mean!?

MartinMueller2003 wrote:sACN is a comparable / companion / precursor (depending on your viewpoint) spec to E1.31. sACN is the common name for the sp...

10 years ago
Forum
DMX
Reply
RE: Enttec USB + 3ch Decoder = Random Blinking?

Vadoo wrote:I also noticed the smallest chip on the Enttec is getting very hot.. Very hot, like burn your finger hot or uncomfortably hot? Burn your...

10 years ago
Forum
DMX
Reply
RE: sACN, e1.31, DMX, what does it all mean!?

E1.31 is basically DMX over Ethernet. There is no translating per say, its an Ethernet control standard. If I device is compliant with the E1.31 spec ...

10 years ago
Forum
DMX
Reply
RE: Enttec USB + 3ch Decoder = Random Blinking?

Vadoo wrote:I notice that list. I was hoping for a recommendation of a good free one that would be easy to use, at least for testing purposes. Why n...

10 years ago
Forum
DMX
Reply
RE: Enttec USB + 3ch Decoder = Random Blinking?

Vadoo wrote:I'm not familiar with any other software. What would you recommend trying? Your first post had this link which has lots of options.

10 years ago
Forum
DMX
Reply
RE: Enttec USB + 3ch Decoder = Random Blinking?

To be fair it sounds like you are dealing with off-brand DMX devices, the only thing I would trust is the Entecc dongle. So the next step is to elim...

10 years ago
Forum
DMX
Reply
RE: Enttec USB + 3ch Decoder = Random Blinking?

Vadoo wrote:I've tried connecting pin 1 at the Enttec but not at the 30ch decoder. I've tried connecting pin 1 at the 30ch decoder but not at the Entt...

10 years ago
Forum
DMX
Reply
RE: Enttec USB + 3ch Decoder = Random Blinking?

Vadoo wrote:I'm connecting to D+ and D- with the scope, so pin 1 isn't used. I've tried connecting the same way to the decoder and no change. No wha...

10 years ago
Forum
DMX
Reply
RE: Enttec USB + 3ch Decoder = Random Blinking?

For DMX you are looking for nice crisp square-waves. No rounded edges or slopes. Ideally your DMX run should be terminated with a 200 ohm resistor bet...

10 years ago
Forum
DMX
Page 2 / 177
Share: