Notifications
Clear all

WS2801 Pixel

14 Posts
9 Users
0 Reactions
8,724 Views
Posts: 68
 thg
Topic starter
(@thg)
Trusted Member
Joined: 17 years ago
[#19212]

Just want to make sure i have this correct before powering them up.

Red wire-DC5volts
White wire-Data
Green wire-Clock
Blue wire-Ground.

Thanks

Thomas


13 Replies
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

Unfortunately there is no "correct" wire color listing - the Chinese strings seem to use whatever color wire they have on hand. The guys at ACL have a Pixel Wire Color (sorry *Colour*) list and the one WS2801 combination for R/W/B/G has:

Red - +5v
White - 0v (Gnd)
Green - Clock
Blue - Data

...but that doesn't mean you have it wrong either... Keep in mind that there is an IN and OUT as well so you have to pick which end to wire up to the the controller. Most recommend the non-chip side as the IN.

The one good thing about 5v strings is they tend to tolerate wiring them up wrong. If you have an extra pixel, you might try just the one if you're worried about blowing up the string...


Reply
Posts: 2171
(@mschell)
Noble Member
Joined: 18 years ago

On the 2801 pixels that I got from Ray, the PCB board in the pixel has some writing on it that tells you a few things.

INPUT is shown on one side of the board. The other side of the board has a big black blob, under which is the IC.

With INPUT facing me, the order of colors is as follows (left to right):

Blue - Data (marked SDI)
Green - Clock (marked CKI)
White - Ground (marked GND)
Red - +5V

Now, depending on the manufacturer, this may be different, but wanted to give you some clues as what to look for...


Reply
pmcpa
Posts: 1390
(@pmcpa)
Noble Member
Joined: 17 years ago

I ecco what the others say... just make sure you have Ground and +5v correct, no damage in getting the other 2 wrong!


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

The 2801's I got from Ray are Red, Green, Blue and Yellow so you never know...


Reply
Posts: 5
(@socaljimh)
Active Member
Joined: 15 years ago

And if you don't like any of the other answers......

I ordered and received a 50 pixel 2801 string from Ray a couple weeks ago. I asked him the same questions and received the below answer---

"RED WIRE: DC5V input +
yellow wire:DATA
greem wire: clock
blue: Ground
input side: is the side with IC"

(the above did work)
So, Input side, pixel up/wires down, Left to Right- DC5v+, DATA, CLOCK, GROUND

I believe the best advice is to contact the supplier and determine how the current run was assembled.

Good Luck!!


Reply
Posts: 68
 thg
Topic starter
(@thg)
Trusted Member
Joined: 17 years ago

Alright with the pixel at the top and the IC on the back side and looking at the in wires from left to right. On the circuitboard it looks like Gnd, cko, sdo, then +5, which is blue, green, white, red wires. That the best I can make out on the boards.

Thanks

Thomas


Reply
mrpackethead
Posts: 2289
(@mrpackethead)
Famed Member
Joined: 19 years ago

Geepers Creepers and the pixels that i have got, all the wires are black. Looking at the pixel unforutly unless you know the PCB is unlikely to help as well. You might need to take one apart and reverse engineer the pin outs... This is one of the key advantages of buying pixels like this, you can have all this extra fun figuring it out, blowing up and destroying a few strings before you get it to work.


Reply
Posts: 1076
 Zeph
(@zeph)
Noble Member
Joined: 15 years ago

OK, it's clear that colors mean nothing from string to string.
Worse, above we have two different physical sequences with + and Gnd reversed, looking at a pixel orieneted the same way.

So is there any electrical way to determine which is which, eg: with a multimeter? Without frying or tearing open a pixel?

Let's assume that the same color is connected to the same function from end to end (after looking at first and last pixels).

I'm thinking that ground and power would have relatively low resistance from end to end. I imagine using a 1.5v battery and a 10k resistor to test this - that should not harm anything, right.

Is there any way to test which is ground and which is 5v without causing harm? For example, can you connect to some voltage which will not harm the pixels if reversed, but which show different measurements fwd/rev? Once you have power and ground, nothing will be harmed by swapping the other two.


Reply
Posts: 2171
(@mschell)
Noble Member
Joined: 18 years ago
thg wrote:Alright with the pixel at the top and the IC on the back side and looking at the in wires from left to right. On the circuitboard it looks like Gnd, cko, sdo, then +5, which is blue, green, white, red wires. That the best I can make out on the boards.

Thanks

Thomas

Given it says "sdo", I would assume this is the Output side. And sdo is the data line.


Reply
Page 1 / 2
Share: