E681 setup - High n...
 
Notifications
Clear all

E681 setup - High number of sequence errors.

32 Posts
11 Users
0 Reactions
14.9 K Views
Barnabybear
Posts: 1583
Topic starter
(@barnabybear)
Noble Member
Joined: 15 years ago
[#19201]

Hi, I'm getting a very high number of sequence errors - could someone cast their eyes over the pdf attached and tell me whats wrong.
Windows 7 32 bit - Vixen 2.1.4.0. - J1Sis 1.0.0.1. - E681 2.20.


31 Replies
rokkett
Posts: 441
(@rokkett)
Reputable Member
Joined: 17 years ago

But the pixels are working correctly, right? I believe the E68X is reporting the sequence error, but still sending the pixel data down stream. I have also seen high numbers of sequence errors reported and still have the device render the pixel data perfectly. I would not worry about that statistic.


Reply
Barnabybear
Posts: 1583
Topic starter
(@barnabybear)
Noble Member
Joined: 15 years ago
But the pixels are working correctly, right?

I don’t have any pixels yet – I was hoping they arrive this weekend, but not looking good now.
I finished assembling the boards last week and was trying to set them up. I know in the J1Sis video it was stated that some errors my occur but I wasn’t expecting that many.


Reply
pmcpa
Posts: 1390
(@pmcpa)
Noble Member
Joined: 17 years ago

Normally indicates a switch, hub, or router isn't properly passing your multicast packets. Check in your internet router and see if there are any settings for multicast. Also, I've found that I get some errors when playing back a sequence on a machine with a gigibit card on a gigibit switch, but the sequence will have no issues when on a 10/100 network switch.... This is from LSP, your results may differ!


Reply
Barnabybear
Posts: 1583
Topic starter
(@barnabybear)
Noble Member
Joined: 15 years ago
Normally indicates a switch, hub, or router isn't properly passing your multicast packets.

Yes - I tried plugging directly into the pc - still the same errors.

I've found that I get some errors when playing back a sequence on a machine with a gigibit card

The pc card is 100Mbps - I'll try it on my laptop and see if it reduces the errors.


Reply
pmcpa
Posts: 1390
(@pmcpa)
Noble Member
Joined: 17 years ago

hmmm... then that is odd... any firewall software on the pc?


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

This might be one of the known bugs. I read about false error reports due to overhead or something. I'm not sure if it applies here but some research in this direction may help.

Brian


Reply
Posts: 1249
(@jstjohnz)
Noble Member
Joined: 17 years ago

I suspect your LSP configuration isn't right. What you are seeing is typical if multiple senders are sending to the same set of universes. There should only be one copy of the E1.31 plugin running.


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

Download SACNView and give that a try - no Vixen/Plug-in in the equation - it's very handy to have on hand for quickie testing.


Reply
Barnabybear
Posts: 1583
Topic starter
(@barnabybear)
Noble Member
Joined: 15 years ago

The bit that is really messing with my head is:
Send #1 universe no errors.
Send #2 universe no errors.
Send #1 & #2 - 51 packets 50 errors.
Send 3 universes – all universes 51 packets 50 errors.
Install a second plugin and send -
#1 universe via #1 plugin and #2 universe via #2 plugin – 51 packets no errors.
#1 universe via #1 plugin and #2 & #3 universes via #2 plugin – #1 51 packets no errors - #2 & #3 51 packets 50 errors.
I'm downloading scanview now.


Reply
Page 1 / 4
Share: