e681 Power supply
 
Notifications
Clear all

e681 Power supply

14 Posts
9 Users
0 Reactions
6,884 Views
Posts: 161
Topic starter
(@teddy)
Estimable Member
Joined: 16 years ago
[#19231]

i just received my e681's from the group buy and am trying to figure out what the best power supply for my needs are. I would preferably like to get something that is water proof or at least resistant.

for now i plan to run the GE Color Effects off of it but in the future want to buy some pixels from ray wu's store and am not sure if i would want to get 12v or 5v ones.

any advice would be greatly appreciated.


13 Replies
Posts: 1744
(@tjetzer)
Noble Member
Joined: 18 years ago

You're going to be hard pressed to find a waterproof power supply that can handle the current draw you're going to need for pixels. Your best bet is to put a power supply similar to this or this into an enclosure.


Reply
Posts: 161
Topic starter
(@teddy)
Estimable Member
Joined: 16 years ago
tjetzer wrote:You're going to be hard pressed to find a waterproof power supply that can handle the current draw you're going to need for pixels. Your best bet is to put a power supply similar to this or this into an enclosure.

Wow much less then I expected. Thanks for this ill order them soon. Any tips on the enclosure?


Reply
Davor
Posts: 221
(@davor)
Reputable Member
Joined: 16 years ago

The E681 should fit a CG-1500 enclosure. WLC Ventures sells them.


Reply
Posts: 161
Topic starter
(@teddy)
Estimable Member
Joined: 16 years ago

i meant for the power supply. or will it fit in the cg-1500 with the board?


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

You may want to look around for rack mount server power supplies. I pulled a few from some old servers that weren't being used. They are flatter (1RU) than normal PC supplies yet have a fair amount of power output. If you get the right one, they can fit into the CG-1500 but it has a fan so it does need fresh air access.

DSC00079

This year with my expanded setup I plan to use an idea from dirknerkle (who else?!) using boat battery boxes. I'm using 5v/30A supplies and will mount them to a sheet of aluminum inside the box to act as a heat sink and keep them stable. The boxes have nice vent holes as well. I am thinking of using a separate (smaller) supply for the E680s just in case there are any surges from the pixel supplies.


Reply
Davor
Posts: 221
(@davor)
Reputable Member
Joined: 16 years ago
budude wrote:

What kind of cable are you using for the power and data lines?


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

I used Cat5 for this setup but will be using normal 4x conductor wire that comes with the pixels for the new stuff.


Reply
Posts: 13
(@mickpat)
Eminent Member
Joined: 16 years ago
Reply
lightman
Posts: 1524
(@lightman)
Noble Member
Joined: 19 years ago
budude wrote:You may want to look around for rack mount server power supplies. I pulled a few from some old servers that weren't being used. They are flatter (1RU) than normal PC supplies yet have a fair amount of power output. If you get the right one, they can fit into the CG-1500 but it has a fan so it does need fresh air access.

This year with my expanded setup I plan to use an idea from dirknerkle (who else?!) using boat battery boxes. I'm using 5v/30A supplies and will mount them to a sheet of aluminum inside the box to act as a heat sink and keep them stable. The boxes have nice vent holes as well. I am thinking of using a separate (smaller) supply for the E680s just in case there are any surges from the pixel supplies.

Nicely done... I think I will do mine similarly.

Regards,
Lightman


Reply
Page 1 / 2
Share: