Technicolor Pixels
 
Notifications
Clear all

Technicolor Pixels

140 Posts
31 Users
0 Reactions
43.4 K Views
timon
Posts: 2149
Topic starter
(@timon)
Noble Member
Joined: 16 years ago

Shouldn't matter, except for the GE's, as long as the pixels have some input protection such as a resistor. If you don't know or want to play if safe bring them up at the same time.

idleup wrote:Is it better practice to apply power to the pixels first or the controller first? I am using the e682 and the board gets power from a dedicated 5vdc wall wart while the pixel power comes from two of the Ray Wu 12vdc power supplies. I am still having problems with pixels going out and am wondering if I should be turning on the pixel power before the board power or visa versa.

Thanks.


Reply
RobG
Posts: 1255
 RobG
(@robg)
Noble Member
Joined: 14 years ago
idleup wrote:Is it better practice to apply power to the pixels first or the controller first? I am using the e682 and the board gets power from a dedicated 5vdc wall wart while the pixel power comes from two of the Ray Wu 12vdc power supplies. I am still having problems with pixels going out and am wondering if I should be turning on the pixel power before the board power or visa versa.

Most of the chips have protection diodes on their inputs, so if you apply voltage to input before you power the chip, the chip will get it's power from input via protection diode. Because of that, you need to power your pixels first.
220-330 resistor on the input will protect it from excessive current (in addition to other good things.)

If you look at chip's specification, you will see that there are few different mac voltages specified. One for the logic, one for the input (which is usually same as logic,) and one for Vo. Logic and input are usually <6V, Vo can be as high as 30V for some chips (not WS2811.) Vo specifies what the output stage can handle.

On a personal note, I think using LDO to lower 12V down to 5V is a really bad design.


Reply
Posts: 615
(@livinglightshows)
Prominent Member
Joined: 14 years ago

So when powering everything off is the best practice to remove power from the board first and then the pixels?

RobG wrote:Most of the chips have protection diodes on their inputs, so if you apply voltage to input before you power the chip, the chip will get it's power from input via protection diode. Because of that, you need to power your pixels first.
220-330 resistor on the input will protect it from excessive current (in addition to other good things.)

If you look at chip's specification, you will see that there are few different mac voltages specified. One for the logic, one for the input (which is usually same as logic,) and one for Vo. Logic and input are usually <6V, Vo can be as high as 30V for some chips (not WS2811.) Vo specifies what the output stage can handle.

On a personal note, I think using LDO to lower 12V down to 5V is a really bad design.


Reply
timon
Posts: 2149
Topic starter
(@timon)
Noble Member
Joined: 16 years ago
RobG wrote:On a personal note, I think using LDO to lower 12V down to 5V is a really bad design.

Why in general? Local regulation is quite common and normally not a problem. I thinking is less likely the LDO is the problem but it's the WS2811 running without an input resistor. The verdict isn't in yet but that's how I'm leaning currently.


Reply
RobG
Posts: 1255
 RobG
(@robg)
Noble Member
Joined: 14 years ago

Let's see, you are powering 2V(red) and 3V(b&g) LEDs from 12V.
LDO burns 7V and WS28xx another 2-3V, that's 16-25% efficiency.
You should use 12V only when there's a need for it (there's more than one LED in series.)
I understand this is the way to combat voltage drop and 12V supplies are common, but it is still bad design.
If you cannot inject power mid way and have to use LDO approach, power it from 6V, 9V at most.


Reply
Page 27 / 28
Share: