Technicolor Pixels
 
Notifications
Clear all

Technicolor Pixels

140 Posts
31 Users
0 Reactions
43.4 K Views
timon
Posts: 2149
Topic starter
(@timon)
Noble Member
Joined: 16 years ago
budude wrote:The maximum temperatures in the spec sheets are usually for the junction temp - not the case temp (the junction temp will be higher...). I ran into a similar issue with the Ren48LSD (v3b) running a standard 7805 with 12v becoming a fingerprint melter...

The data sheet contains the temperature rise which is about 15C junction to case and 55 junction to ambient air.

kingofkya wrote:Generally you get a better power supplies.

Has one one tested the pixel regulator? to see if maybe its too slow to react to a bad power supplies spike eventually killing the ws2811 or something. Theses are just such a simple design it makes me think bad power.

So thous of you with issues are you all running rays power supplies?

That not likely a problem. The input and output caps work with the LDO to limit the spike.


Reply
timon
Posts: 2149
Topic starter
(@timon)
Noble Member
Joined: 16 years ago

I've been doing something that may or may not help the pixels and moisture issue. I'm keeping my pixels on 24x7. Right now it's just the controller running in test mode but once the show is up I'll leave a no show sequence running the keeps the lights on at a low lever just to keep them warm. May not help but I don't think it will hurt.


Reply
Posts: 615
(@livinglightshows)
Prominent Member
Joined: 14 years ago

I do not have an OScope. Is there something I can put on the power supply output to catch those spikes? like some kind of DC-DC converter?

kingofkya wrote:Generally you get a better power supplies.

Has one one tested the pixel regulator? to see if maybe its too slow to react to a bad power supplies spike eventually killing the ws2811 or something. Theses are just such a simple design it makes me think bad power.

So thous of you with issues are you all running rays power supplies?

Also to check this theory?
Get a oscilloscope,
Use AC Coupleing,
Set to about 10micro voltas
And see what it looks like.

Should look something like this. (top)

But if you see something odd like a square, saw tooth or bad spikes it may be your issue.


Reply
Posts: 1076
 Zeph
(@zeph)
Noble Member
Joined: 15 years ago
Steven010 wrote: First, I would ask them what happens to part if VDD =0V and Data in = 5V? especially if an LED is attached?

I recall being startled a while back when I was running a moving light down a short string on the bench and I realized that the pixel power was disconnected. Apparently the pixels were drawing power from the data line (driven by a 5V Arduino Uno) - enough to light one pixel at a time. I'm guessing that power was going through protection diodes on the first pixel. Not recommended and I cut all power when I realized what was going on, but the string does not appear to have been damaged.

I forget which chips I was using, may have been the 8806.

(I had been surprised another time when I connected two Arduinos via serial TX/RX to test round trip timing -- when I disconnected the power from the second Arduino and before I disconnected power from the first, I saw that the test was still running! The unpowered Arduino was apparently drawing enough power from the powered Arduino via the two connected IO pins to operate the code, send data back, and light onboard LEDs. I guess the pixel situation was similar.)


Reply
Posts: 615
(@livinglightshows)
Prominent Member
Joined: 14 years ago

Is it better practice to apply power to the pixels first or the controller first? I am using the e682 and the board gets power from a dedicated 5vdc wall wart while the pixel power comes from two of the Ray Wu 12vdc power supplies. I am still having problems with pixels going out and am wondering if I should be turning on the pixel power before the board power or visa versa.

Thanks.


Reply
Page 26 / 28
Share: