Technicolor Pixels
 
Notifications
Clear all

Technicolor Pixels

140 Posts
31 Users
0 Reactions
43.4 K Views
Posts: 95
(@danolgb)
Estimable Member
Joined: 17 years ago
Steven010 wrote:The LDO was hottest point, reaching peaks of 70C (~158F) degrees. Never dropped out of regulation, never shut off. However, pretty hot. But I would think that being used outside in winter, the ambient temperature would work in its favor. Still not convinced we have root cause of failures....

\
Wouldn't it stand to reason tho that you might get different results running it uncased than when enclosed in the pixel? The plastic might be trapping the heat.

Mine never seemed to fail while the lights were on or while power was supplied. It was immediate on powering them up. They had last operated just fine. So maybe something about trapping the heat when power was removed? Just reaching here.


Reply
dsmjuggalo
Posts: 663
(@dsmjuggalo)
Prominent Member
Joined: 15 years ago

im using a atx power supply


Reply
timon
Posts: 2149
Topic starter
(@timon)
Noble Member
Joined: 16 years ago

That actually goes along with my "lip" and "Pinky" test. My pinkey said it was not that hot but my lip yelled about it.:lol:

Actually 70C is not that bad. But yes we need to know what the temperature inside the case is. I've talked to ray about molding a thermocouple which is attached to the LDO tab so we can measure it. I'll press Ray on that during our next chat.

Anyway the LDO is rated at a junction temperature of 150C. I don't have the data sheet with me right now but we need to add in the junction to case temperature rise.

True for us in the states we have cold weather to help keep the cool but down under they have a big heater in the sky that wants to heat them up.:lol:

Steven010 wrote:John,

Been testing some more, here are some more details for you;

Trying to stress data-in pin, so far no luck. So I turned to Thermal inspection. turned pixel to all bits high (full White) at 12.5V (worst case I can come up with), let run to 30 minutes.
The LDO was hottest point, reaching peaks of 70C (~158F) degrees. Never dropped out of regulation, never shut off. However, pretty hot. But I would think that being used outside in winter, the ambient temperature would work in its favor. Still not convinced we have root cause of failures....

Dropping voltage to 7V helps significantly with respect to temp...

Shown below is PCB and Thermal image...


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

The maximum temperatures in the spec sheets are usually for the junction temp - not the case temp (the junction temp will be higher...). I ran into a similar issue with the Ren48LSD (v3b) running a standard 7805 with 12v becoming a fingerprint melter...


Reply
kingofkya
Posts: 2165
(@kingofkya)
Noble Member
Joined: 15 years ago
idleup wrote:I am using the power supply from ray on my pixels that keep going bad. I have some technicolors on a PC power supply (converted) and have not had any problems. How can I protect against those spikes or even see if that is what occurring?

Generally you get a better power supplies.

Has one one tested the pixel regulator? to see if maybe its too slow to react to a bad power supplies spike eventually killing the ws2811 or something. Theses are just such a simple design it makes me think bad power.

So thous of you with issues are you all running rays power supplies?

Also to check this theory?
Get a oscilloscope,
Use AC Coupleing,
Set to about 10micro voltas
And see what it looks like.

Should look something like this. (top)

dsp4.figure 5

But if you see something odd like a square, saw tooth or bad spikes it may be your issue.


Reply
Page 25 / 28
Share: