Pixels Acting Errat...
 
Notifications
Clear all

Pixels Acting Erratically

25 Posts
8 Users
0 Reactions
21.1 K Views
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

Have you tried Makuna Neopixelbus WS2813 to drive these pixels ?
I have also read that Fastled WS2813s will drive them .

You could modify an e131 sketch to test/compare with .
Other than that ,it may be some settings or configurations within Wled you may have overlooked.
Wled is expecting to see Wifi channel 1 ,so you may want t check your router's wireless settings.


Reply
Posts: 740
(@ezellner)
Prominent Member
Joined: 11 years ago
Guy wrote:OK, I wired a single pixel about 10' from the power/data source and 15' from the rest of the LED strip. The single pixel is behaving like I want it to, but the rest of the strip turns on random colors (mostly blue/green/white) throughout the entire strip. WLED is programmed to only light up the first 15 pixels, but the entire string turns those colors.

I am able to control the single pixel I have in the middle of the wire, but none of the others. If I disconnect the strip they all go out (obviously) and if I plug it back in they remain dark.

Still seems like a wiring issue, but the wiring simply isn't that complex!

Any other suggestions on things to test? Is there a good way to test if there is interference on my wires? I'll look to order one (two?) of those null pixels, but who knows how long they will take to get here. 🙂

-Guy

A single pixel doesn't have the oomph to get that additional 15 feet. Does the strip light properly when connected directly to the controller rather than a long distance away?


Reply
Jeff Millard
Posts: 1450
(@jeff-millard)
Noble Member
Joined: 19 years ago
Guy wrote:OK, I wired a single pixel about 10' from the power/data source and 15' from the rest of the LED strip. The single pixel is behaving like I want it to, but the rest of the strip turns on random colors (mostly blue/green/white) throughout the entire strip.
-Guy

These two sentences indicate that either the first (the one that is behaving) pixel is bad and not properly passing data to the second. Or, the second pixel is bad and isn’t using the data it’s getting correctly. My reaction to the behavior you described would be to cut them both clear and toss them. Start at pixel three, now known as the new pixel one.

And since you’ve installed what could be described as a null pixel at 10 feet, that being pixel one, it’s probably not that one.
Jeff


Reply
Posts: 94
(@srmorgan)
Estimable Member
Joined: 7 years ago

In new To this but is it possible to use a 25’ piece of cat5 wire to see if that clears up the signal. I heard it can have transmission distances of over 100’. Because if the first (new) pixel works after 10’ but the problem returns, 15’ is to far for a signal run. What gauge wire are you using. Is it shielded. Is there anything in that part of your house that could be putting EM interference. Our just adds another pixel in the 15’ section or an f-amp in place of the new first pixel.


Reply
Posts: 11
 Guy
Topic starter
(@guy)
Active Member
Joined: 7 years ago
ezellner wrote:A single pixel doesn't have the oomph to get that additional 15 feet. Does the strip light properly when connected directly to the controller rather than a long distance away?

At this point I'm going to wait until those null pixel buffers show up before I do much more testing, and shipping is experiencing huge delays so I'm going to probably be quiet for a minute until those arrive.

After moving my "null pixel" around, I found that the wire had effectively ripped out the solder pads. I tried a new pixel and it did the same thing after some movement. This may have contaminated some of my research, and it may have actually burnt out one of the pixels (as Jeff indicated). I'll wait for my new hardware to arrive, and see what happens when wiring those guys up!

My plan is to solder both data lines to the same pin on the null pixel (rather than use two null pixels) since it is a redundant data line. Does anyone see a problem with that?

Thanks again for all your help!

-Guy


Reply
Page 3 / 3
Share: