MikeKrebs wrote:on your PC.
open a command prompt.
ipconfiglook for the IPV4 address. Is it 192.168.1.xxx? If not, that is definitely the problem. If so, what happens when you type 192.168.1.96 in your browser?
The line "FPPD is not running" is troublesome but first the networking fix.
Make sure your dongles are plugged in when the PB boots. You want them discovered on startup.
This is a case where the zoom room would be helpful because network issues when you are not network savvy are very frustratingly slow in the forum.
I have heard of the zoom room. I am interested if someone has a link. I looked at all my connected devices in my router and they were all 192.168.xxx. I tried the command prompt but I'm on Mac so I tried some commands I googled. with no luck. I bought this pocket beagle preloaded to avoid all of this but I ended up creating this mess. It definatly says FPPD is not running. I am getting the WIFI hot spot QR code piping up every few seconds too. I agree w/ the network issues being a pain in an online forum. Slow for sure and hard to articulate. Thanks for the advice. I will press forward and google the Zoom Room.
Thank you!
on your PC.
open a command prompt.
ipconfig
look for the IPV4 address. Is it 192.168.1.xxx? If not, that is definitely the problem. If so, what happens when you type 192.168.1.96 in your browser?
The line "FPPD is not running" is troublesome but first the networking fix.
Make sure your dongles are plugged in when the PB boots. You want them discovered on startup.
This is a case where the zoom room would be helpful because network issues when you are not network savvy are very frustratingly slow in the forum.[/QUOTE
I forgot to add that when I type the IP in I get Safari can not reach this page. Initially safari would pull the falcon page up with my GUI to make my changes. I did a reset through the on board menu and probably wiped some of the settings. Getting some kind of communication with it is my main concern, like you were saying.
Officially it is the xLights zoom room and found off their web site.
https://xlights.org/
This is the link on their page to get the zoom running. Click the link and install the zoom software and join the meeting.
https://xlights.org/download/1944/
Is one of the connected devices on your router, the Kulp k4-PB?
The cable from the wired ethernet, does it light up the port when you plug it into the router/switch? If you watch the network status in your router, what comes and goes as you plug and unplug?
A somewhat easy fix is to just reload the SDCard with the latest FPP or if you have a second card, do it there. Again the zoom room could help you in a very quick manner.
MikeKrebs wrote:Officially it is the xLights zoom room and found off their web site.
https://xlights.org/This is the link on their page to get the zoom running. Click the link and install the zoom software and join the meeting.
https://xlights.org/download/1944/Is one of the connected devices on your router, the Kulp k4-PB?
The cable from the wired ethernet, does it light up the port when you plug it into the router/switch? If you watch the network status in your router, what comes and goes as you plug and unplug?A somewhat easy fix is to just reload the SDCard with the latest FPP or if you have a second card, do it there. Again the zoom room could help you in a very quick manner.
Thank you for the link! Loading the FPP software to a different card has crossed my mind. I have downloaded the tools necessary to burn the image to my card. Working through that when I have time. I actually ordered a new controller so I can get my display going and will continue to restore the initial controller when I have the display complete. I?m also trying to get more proficient with x-lights. Add to all of this I have a MacBook I?m trying to get the hang of. I know I will be expanding so the extra controller will be used. As far as the router, the controller is identified as the IP address followed by FPP. When connected via Ethernet I see ?on? as the status, it changes to off when powered off even now. The adapter flashes the green and yellow traffic lights. All indications show that it?s connected but will not respond when I type in the address. Someone told me I should be able to SSH in? Going to look more into that when I can get back to it. I plan to load a new SD card either way. I really appreciate all the help y?all!
