There is a feature of the F16V2 that I have noticed has gone unmentioned in this discussion that I found to be extremely helpful. The virtual string capabilities allowed me to mix RGB and BRG pixels on the same output without needing to make any changes to the patching or settings on my sequencing software (mini tree used RGB bullets and star on top used a BRG strip). This was a huge time saver for me.
I mentioned it...but this discussion is like trying to pry LOR software out of a LOR fan boys hands...LOL. You can lead 'em to water...
Sent from my LG-H811 using Tapatalk
MindTrik wrote:You didn't...the issue here isn't loyalty..it's steering someone who doesn't have a board to simply...THE best option as of right now. You shouldn't regret a purchase after a purchase. Since you are just starting...you should just go ahead and get the best option. Also...don't forget the F16V2 has FOUR native DMX outputs on top of the string outputs. That's HUGE!Sent from my LG-H811 using Tapatalk
I went back and lookes at the specs once again between the two and saw the 485. That will run my renards if i decide to add them back in.
Do u know if the falcons are in stock?
Check falconchristmas.com I use renard on mine as well as LOR. PM sent
Sent from my LG-H811 using Tapatalk
Ill check with em im leaving for our disney trip next week so ill wait till we get back to order it all up. Thanks for everyone help in getting the best controller. I was hoping mararunr would get back at me i like his style of mega tree
Sent from my iPhone using Tapatalk
Gump, no I don't necessarily have any drawings per se. My trees are 32 strands by 50 pixels with 4" spacing with each strand attached to 1/2" PVC. The first pixel is about 15" above ground level and the bottom ring of the tree is made up of three 10' 1/2 PVC pieces. The bottom ring is wired to rebar fashioned into tornado anchors at four points (rebar driven into the ground at opposing 45 degree angles creating an 'X' which is very solid - withstood 63 mph winds this past winter). Tree trunk is 2.5" pvc set inside a 3" sleeve that is concreted into the ground (240lbs of concrete in a four foot by 18" hole). About half way up the tree is a second ring of 1 1/2 10' PVC pipe to help maintain the shape. Guide wires run from the top (eyelet screws in wooden topper) and the middle (S hooks attached to dryer vent clamp) down to the tornado anchors (guide wires inside tree shape for safety). Tree topper is a 12" across wooden cog wheel design with a screw in the middle of each of the 32 cog locations. There's a hole on the back side of each pvc strand near the top. The hole and screw work together along with gravity to hold strands in place (slide strand hold over screw head, strand is now held in place horizontally by the cog cut out and vertically by the weight of the pvc cause the lip of the hole to sit over the screw head). The star at the top is a 3-foot 45 pixel star (90 actually because it's a double-sided star) made of wood attached to PVC that runs through a hole in the tree topper down into the trunk a little ways (put a piece of rebar in the PVC to add stability weight). There is also an additional 50 pixels running up the trunk of the tree. I run 5v pixels and a F16v2 so it takes 2 PSUs (900 on the first, 840 on the second) and 3 ports on the controller (600 pixels on 1st and 2nd, with 540 on last). I power inject every 50 pixels. I only had one tree my first year (Christmas 2014), and added the second last summer during construction phase repeating what I did for the first so I know it's a process that can be repeated. The trees are about 21 feet tall in total. I made a wooden scaffolding that I can put up or take down in about 30 minutes to be able to put the trees up (too cheap for steel, wanted something that I could store easily, and didn't want to spend tons of money on something that only gets used twice a year - setup and tear down). By the way, I'm a wood and pvc maker as opposed to steel/aluminum/metal maker if that's not apparent. Like I said, my display withstood max winds of 63 mph this past winter and sustained winds of 42 mph.
Hope this helps, mv
Awesome! How did you get ur pixels in the pvc? Any pics of that? I currently have a piece of a mega tree but its incans now. Im thinking i can use some of that and mounting my pixels some how.
Sent from my iPhone using Tapatalk
I just want to add a couple of reasons to use the FalconF16V2. First when I started early in 2015 to build a RGB display I ordered an AlphaPix from Holiday Coro, it had problems with the firmware and David basically treated me as a dummy as I was new to the hobby, however he later appoliged and corrected his problems. I in the meantime formed a relationship with Dave Pitts and ordered three Falcon boards. Dave at Holiday Coro offered to take back the AlphaPix and give me credit which I declined. I use his controller on a concession stand and it works just fine, however I would not run my display with anything else but a Falcon period. My show uses a Raspberry PI B+ running three Falcon boards for convenience. They work flawlessly and I actually have a fourth on order why, they perform and the distance from the controller to pixels with the Falcon is not matched by any other controller. My show turned on Thanksgiving night and never missed until I turned it off Jan 2nd and was not even there for a week we went on a cruise.
Just my two cents worth
Kent
BTW I want to agree with an earlier post, you shouldn't regret a purchase after a purchase, if you get the Falcon you won't ever regret having that controller
I second David Pitts and the falcon group. I didn't know anything about pixels at all in December. And now I feel that thanks to their support and forums and advice I have a clear understanding. I ordered 5 of them 4 with expansions
Sent from my iPhone using Tapatalk
Thanks to all the help here ive made my decision to join everybody else here. Imma order the falcon controller as well.
Sent from my iPhone using Tapatalk
