Hacking LED Strings...
 
Notifications
Clear all

Hacking LED Strings from DX

44 Posts
8 Users
0 Reactions
11.4 K Views
Posts: 499
(@frederic)
Honorable Member
Joined: 14 years ago
CaptKirk wrote:They are strings with one segment of red, one green and one blue interleaved.
CaptKirk wrote:if you wanted to individually control the three colors by doing bridge conversion on each individual color. Hmmm... interesting idea.

Since these things have two neutrals and three "hots", one for each color, one can control them with a lighting controller such as a Renard. The string I experimented with was purchased off ebay as a multi-color 50-led string. They were arranged as three strings, one of each color, and the LED count was unequal. There were 15 blue, 17 green, and 18 red.

Here is a crude schematic done in Visio of all things:

fairy 1

The resistor, first diode, and capacitor produce half-wave AC as well as a low-pass filter. The two LED's and the dashes between them represent the string of that color (red, green or blue).

I tried this and it works, using three of the four diodes in the fairly light controller box that came with it. I added the capacitors and resistors out of my junk drawer, using a web-based calculator to determine the appropriate values, and I used the closest ones I had.

I didn't put them out this year because I only had the one string because I found post-Christmas sale lights to be far cheaper in the local home centers and don't have these kinds of tweaking necessary. What I did was take multi and white strings and interleave them myself, then hung those on the eaves so they can be colorful, or full white. Seemed easier at the time.

I wanted to share this in case it's useful to someone.


Reply
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago

I'm getting an error with the attachement now too.

What I was proposing is to hard-wire the control lines to the existing transistors. So.. looking at the bottom of your board, there's the row of pins that make up the "vertical controller board". The first one (far left) appears to be the power coming in. The next four look to be the control lines, you can see them tracing down to the middle pins of the 4 transistors. The next pin, looks to be the GND line. From the image you can see the trace as it goes down and connects to the right hand pin of each of the transistors.

So.. my theory is.. if you take each of the four control lines.. and strap them to the GND pin (one piece of wire connecting all four to the GND pin).. it should force the lights be on all the time. Once that is achieved.. you can plug them into the SS24.

MacSHROOM wrote:ive tried on my PC and my ipad and it says that's an invalid attachment . I believe I understand what you said .I have LED fairy lights 10m -30m. I want to run them with a renard ss24.
I know I attach the ac input to the two ~'s on the bridge rectifier. but then what exactly do I do?
the hack described here says there are 3 that go to lights and to gang them , and the other two,commons? get soldered together.
I think these lights have 4 wires that go to bulbs not 3. and there would be just one 'common' wire.instead of the 2 common in the hack described here.
some of the 8 mode controller boxes had the second common unattached to anything ,just glued in beside the common at the end of the row,but not connected to any pad or touching any other wire. not connected to anything . I stripped and soldered the unattached wire, to the common .hope that works .
so what you are saying it to gang the 4 wires that go to bulbs , and attach the single common to the bridge rectifier? and do the bulbs get connected to the + or the _ on the rectifier?or does that matter? thanks .

Reply
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago

I think I fixed the attachment. That was weird.. as the image showed up on the PC that I used to upload the file. But didn't show up on any others.


Reply
Posts: 92
(@macshroom)
Estimable Member
Joined: 13 years ago

I understand what you are saying.im pretty sure I do anyway .but I am throwing 8 ch control boxes and boards away. I am using 1amp bridge rectifiers.so its solder 4 wires that lead to bulbs together and attach them to the + on the rectifier,attach the lone common to the - on the rectifier, and the A/C to the two ~~'s on the rectifier?


Reply
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago

Oh .. ok.. I would have thought to use the rectifier built into the box (save $).

I think you may have the leads to the LEDs reversed. My expectation is that the four leads would want to connect to the GND (-) of the Bridge.
The common would be to (+). However, in this instance.. you can "try". If they don't light, then reverse them.

FYI.. if you have a "simpleREN" or "ren64", you could wire up control lines to each of the four channels. Then you would have a four channel LED string. (More options for blinking/control)

MacSHROOM wrote:I understand what you are saying.im pretty sure I do anyway .but I am throwing 8 ch control boxes and boards away. I am using 1amp bridge rectifiers.so its solder 4 wires that lead to bulbs together and attach them to the + on the rectifier,attach the lone common to the - on the rectifier, and the A/C to the two ~~'s on the rectifier?

Reply
Posts: 92
(@macshroom)
Estimable Member
Joined: 13 years ago

thanks . my rectifiers and heat shrink finally arrived today . time for some pink Floyd and soldering . ill let you know how it works out . I appreciate your help . thanks very much for your time .


Reply
Posts: 92
(@macshroom)
Estimable Member
Joined: 13 years ago

Okay,so i spent the afternoon so far,soldering the snap connectors to a bunch or lengths of wire. Before i start melting the heat shrinks on them,i tried adding a rectifier to one of the strings with the 4 wires going to bulbs and one lone common. Grouped the 4 together and soldered them to the -. Soldered the common to the +. The two a/c to the ~~'s on the rectifier.works like a charm. Left it on for a minute to see if anything burnt or melted or smelled funny.works great.
I enjoy all the soldering very much. Its very calming.which is lucky considering how much is ahead of me.
Only problem I've had is skinning the ends of the fairy light wire.i have a 22 awg stripper and it doesn't quite do the job.I'm gettin by.
Thanks for your help LabRat.
Hope you have a great evening.


Reply
Posts: 92
(@macshroom)
Estimable Member
Joined: 13 years ago

Any tips on how to weather proof the connection? The bridge rectifier needs covering somehow.it costs more than $9/2ft of heat shrink here and thats is more than im willing to pay to cover these connections.
Thanks.


Reply
Posts: 92
(@macshroom)
Estimable Member
Joined: 13 years ago

Im considering tape and leaving it to fate. Or maybe a tube of silicone like i use on my taps and sink.
Maybe just a fold of duck tape.just cut a big piece and sandwitch the rectifier.press it sealed really good.
I can wrap the rectifier with tape,and heat shrink either end of it.
I have tonnes of heat shrink i got really cheap from China.but none of it is quite big enough to go over the rectifier.


Reply
Posts: 92
(@macshroom)
Estimable Member
Joined: 13 years ago

using bags and twist ties.done .ill make it better for next year .


Reply
Page 4 / 5
Share: