Hacking LED Strings...
 
Notifications
Clear all

Hacking LED Strings from DX

44 Posts
8 Users
0 Reactions
11.4 K Views
Posts: 92
(@macshroom)
Estimable Member
Joined: 13 years ago

I can edit posts, how do i delete my posts?
Thank you.


Reply
Posts: 92
(@macshroom)
Estimable Member
Joined: 13 years ago
image

Reply
Posts: 92
(@macshroom)
Estimable Member
Joined: 13 years ago
image

Reply
Posts: 92
(@macshroom)
Estimable Member
Joined: 13 years ago

Okay got em up. Thats the front and back.


Reply
Posts: 92
(@macshroom)
Estimable Member
Joined: 13 years ago

I got the photos of the board posted . anyone know what to do now? thanks .


Reply
Posts: 92
(@macshroom)
Estimable Member
Joined: 13 years ago

if I do this wrong, whats the worst that can happen?will it ruin my RENARD SS24?


Reply
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago
MacSHROOM wrote:

Looks to me like your power is arriving on the 2 pins to the lower right. Those traces go up to the 4 diodes (aka.. your bridge rectifier), and you are getting DC power going to the control circuit (the board that is plugged in vertically).

My guess .. would be that +V is going to the pin on the LEFT, and the next four are the control lines. So.. in theory.. if you cut away the control board
and hooked your REN control lines to the four pins that are the left most of what could be described as the "third row up from the bottom"... you would have computer control of those lights.

Don't have tools here to edit the image.. sorry.

Did that make sense?


Reply
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago

Just a second.. what type of controller are you using? I may not have answered the question being asked.

I was assuming you had a NON SSR series controller, and that you wanted to control each of the 4 strands individually.
If you are using a controller that has an onboard SSR, and you just want to strap the leds to be on all the time, then I think you want to..

a. Disconnect that vertical board (cut it off?)
b. strap the 5 connectors highlighted in this image together (hold on.. having trouble uploading image).

(That's my best guess... check the .sig for standard disclaimers)


Reply
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago

Here it is!

Temp1

Reply
Posts: 92
(@macshroom)
Estimable Member
Joined: 13 years ago

ive tried on my PC and my ipad and it says that's an invalid attachment . I believe I understand what you said .I have LED fairy lights 10m -30m. I want to run them with a renard ss24.
I know I attach the ac input to the two ~'s on the bridge rectifier. but then what exactly do I do?
the hack described here says there are 3 that go to lights and to gang them , and the other two,commons? get soldered together.
I think these lights have 4 wires that go to bulbs not 3. and there would be just one 'common' wire.instead of the 2 common in the hack described here.
some of the 8 mode controller boxes had the second common unattached to anything ,just glued in beside the common at the end of the row,but not connected to any pad or touching any other wire. not connected to anything . I stripped and soldered the unattached wire, to the common .hope that works .
so what you are saying it to gang the 4 wires that go to bulbs , and attach the single common to the bridge rectifier? and do the bulbs get connected to the + or the _ on the rectifier?or does that matter? thanks .


Reply
Page 3 / 5
Share: