ESPixelStick - E1.3...
 
Notifications
Clear all

ESPixelStick - E1.31 WiFi Pixel Controller

948 Posts
178 Users
0 Reactions
503.7 K Views
sporadic
Posts: 1199
Topic starter
(@sporadic)
Noble Member
Joined: 14 years ago
cengiz wrote:Hello,
Apart from the espixelsitick V3 flash tool, I want to install it with arduino ide software. I get the following errors. What am I doing wrong?

Thank you.

C:\Users\istan\Documents\Arduino\libraries\ESPAsyncUDP-master\src\AsyncUDP.cpp: In member function 'bool AsyncUDP::listenMulticast(ip_addr_t*, uint16_t, uint8_t)':

C:\Users\istan\Documents\Arduino\libraries\ESPAsyncUDP-master\src\AsyncUDP.cpp:254:57: error: 'udp_set_multicast_netif_addr' was not declared in this scope

udp_set_multicast_netif_addr(_pcb, multicast_if_addr);

^

C:\Users\istan\Documents\Arduino\libraries\ESPAsyncUDP-master\src\AsyncUDP.cpp:258:36: error: 'udp_set_multicast_ttl' was not declared in this scope

udp_set_multicast_ttl(_pcb, ttl);

^

exit status 1
Error compiling for board Generic ESP8266 Module.

Go over the README.md file again and make sure you are meeting all the dependencies. Sounds like you are on an older version of the ESP8266 core.


Reply
Posts: 19
(@cengiz)
Active Member
Joined: 11 years ago

Thanks for the quick response.

It was solved with the hint you had. I enter the SSID and password correctly but it is not connected. It connects when I install it with Flash tool. It does not connect with Arduino ide. Now where is wrong.


Reply
Posts: 19
(@cengiz)
Active Member
Joined: 11 years ago
cengiz wrote:Thanks for the quick response.

It was solved with the hint you had. I enter the SSID and password correctly but it is not connected. It connects when I install it with Flash tool. It does not connect with Arduino ide. Now where is wrong.

Solved

The problem is solved, connecting to the network ... The current problem says the page can not be found. How to solve this problem.


Reply
Posts: 401
(@kensington)
Reputable Member
Joined: 11 years ago

That error is usually indicative of a problem with the IP address or the network timing out. When I had lot of traffic on my show router, I would routinely get that error.

Common fixes:

1. Make sure you have DHCP enabled when you set up the ESPixelStick, and it will pull the address from the router.

2. If you chose a static IP at setup, make sure the static IP address is on the correct subnet on your router. For example, home routers often use the 192.168.0.1 or 192.168.1.1 subnets, but if the third number in the IP address doesn't match between the ESPixelStick and the router, you'll be able to connect to the network but you'll never find the ESPixelStick page because it is on a different subnet.


Reply
Posts: 34
 rodb
(@rodb)
Eminent Member
Joined: 16 years ago

All,

I have just found and built an ESPixel and it is great works very well for my simple test.

Anyway is there likely to be a group buy of the power supply boards this year. I really like the v2 design and would be keen to purchase some. With or without the components. I'm able to solder all the parts down including the PSU chip no problem.

I may have missed this announcement if so apologies or where I can purchase outside of this forum. I am based in the UK so would either need international shipping form the USA or a UK based vendor.

Or is there somebody selling just PCB's I can sort the rest out myself.

Regards,
Rod Boyce


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

Rob,
Shelby's ESPixel Stick seems to be only available as a completed unit. He sells them on Amazon.
The DIY corollary of this device are the Pixel Pops boards. They are NOT clones as the ESPixel Stick, but do run the same software.
Info is in the wiki found here:
http://www.doityourselfchristmas.com/wiki/index.php?title=ESPixel_Stick_%26_ESPixel_Pops

rodb wrote:All,

I have just found and built an ESPixel and it is great works very well for my simple test.

Anyway is there likely to be a group buy of the power supply boards this year. I really like the v2 design and would be keen to purchase some. With or without the components. I'm able to solder all the parts down including the PSU chip no problem.

I may have missed this announcement if so apologies or where I can purchase outside of this forum. I am based in the UK so would either need international shipping form the USA or a UK based vendor.

Or is there somebody selling just PCB's I can sort the rest out myself.

Regards,
Rod Boyce


Reply
Posts: 19
(@cengiz)
Active Member
Joined: 11 years ago

Everything is okay, version 3.0 okay.

DMX512 mode only 170 channels are working. Could this be why?

Has anyone tried V 3.0? I tried running V2.0 without any problems.

3.0 dmx mod sadace 170 channels


Reply
Posts: 19
(@cengiz)
Active Member
Joined: 11 years ago

I tried 3 different robots. The address does not get a signal when it rises above 170. Help please.

v2.0 512 channels are working. V3.0 only 170 channels


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

DMX serial output cannot do more than 512 channels. That is a limit of the protocol. Renard Serial protocol can go higher. If you are doing pixels then turn off DMX and you should be able to increase the pixel count.


Reply
Posts: 19
(@cengiz)
Active Member
Joined: 11 years ago
MartinMueller2003 wrote:DMX serial output cannot do more than 512 channels. That is a limit of the protocol. Renard Serial protocol can go higher. If you are doing pixels then turn off DMX and you should be able to increase the pixel count.

Thanks for the answer,

V3.0 espixelstick mode DMX512

There are different stage lights at the workshop Robe brand. Address can be given. No problem when I connect to espixelstick at addresses 1-170. The stage robot does not receive a signal from the dmx to raise the adrese to 171 or higher.

When I try the same operation with v 2.0 dmx 512 mode espixelstick, all addresses are running smoothly.


Reply
Page 85 / 95
Share: