ESPixelStick - E1.3...
 
Notifications
Clear all

ESPixelStick - E1.31 WiFi Pixel Controller

948 Posts
178 Users
0 Reactions
503.7 K Views
Posts: 171
(@dmjpixel)
Estimable Member
Joined: 11 years ago
gocats7 wrote:Those of you mounting a PS with the pixelstick, what enclosures are you doing? I have considered the cg500 or a section of 3" PVC would hold both. Looking for ideas to house both and figure this has already been worked out by those using these for a while.

Sent from my Pixel 2 XL using Tapatalk

So far I have mounted a PS and power dist board in a CG1500 and have the stick in thin-walled PVC tube about 5' from the case - I place the case under a bridge deck on our driveway but secure the stick on the gate post. Plan on building a CG case today with a stick in it as well since the prop sits right next to where the case will go.


Reply
Posts: 34
(@juddboz80)
Eminent Member
Joined: 12 years ago

Are these available for purchase anywhere??


Reply
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago
gocats7 wrote:
Does anyone have similar recommendations of a PS to include in the same tube mount with the controller? This is a pretty large thread and search returns a LOT of results for about anything I put in.

https://diychristmas.org/vb1/showthread.php?8293-My-generic-ESPixelStick-enclosure&highlight=generic+enclosure


Reply
sporadic
Posts: 1199
Topic starter
(@sporadic)
Noble Member
Joined: 14 years ago
Juddboz80 wrote:Are these available for purchase anywhere??

The last of my stock for this year is arriving at Amazon today and should be available later tonight or early tomorrow. Possibly delayed a bit given how busy they are. I've been getting many requests, so this last batch will probably go quick once they become available - http://amzn.to/2AfFEK1 . I should have more available around February.
-shelby


Reply
TheLost
Posts: 189
(@thelost)
Estimable Member
Joined: 10 years ago
sporadic wrote:The last of my stock for this year is arriving at Amazon today and should be available later tonight or early tomorrow. Possibly delayed a bit given how busy they are. I've been getting many requests, so this last batch will probably go quick once they become available - http://amzn.to/2AfFEK1 . I should have more available around February.
-shelby

Sweet.. I had a small 'mishap' with a very cheap PSU this week and one of my ESPixelSticks went out in a blaze of glory and magic smoke.
I had to dig into my reserves to keep things running 🙁

I'll be keeping an eye on amazon 🙂


Reply
Posts: 231
(@mwestling)
Reputable Member
Joined: 14 years ago

Ok, noob question here. I have got 9 of these working for arches, etc. that are using only 170 pixels. I have read where folks are running many more pixels that that so I made a sign that is 9x50 pixels for a total of 450. In the ESPixelStick interface, I can run a successful rainbow and chase test and all pixels light. (ESPixelStick is set to 450 pixels) Now I try to set it up in Vixen 3 and cannot get anything to light. I have it setup with 3 universes, 208-210, 510 addresses for 208 and 209, and 330 for 210. I have universe 208 with an address count of 510 in the ESPixelStick interface. I have also mapped the element to all 1320 outputs of the ESPixelStick (E1.31) controller in Vixen. I try to send anything from vixen and nothing happens. I have all my ESPixelSticks and Vixen set to Unicast and have static IPs setup for everything, and all my other elements work fine but I cannot get this darn sign/matrix/grid to work.

I have read where ESPixelStick will roll over to the next universes if you have more than 170 pixels listed in the interface. I am at a loss here and could use some Vixen setup help using more than 170 pixels off a single ESPixelStick.


Reply
sporadic
Posts: 1199
Topic starter
(@sporadic)
Noble Member
Joined: 14 years ago
mwestling wrote:Ok, noob question here. I have got 9 of these working for arches, etc. that are using only 170 pixels. I have read where folks are running many more pixels that that so I made a sign that is 9x50 pixels for a total of 450. In the ESPixelStick interface, I can run a successful rainbow and chase test and all pixels light. (ESPixelStick is set to 450 pixels) Now I try to set it up in Vixen 3 and cannot get anything to light. I have it setup with 3 universes, 208-210, 510 addresses for 208 and 209, and 330 for 210. I have universe 208 with an address count of 510 in the ESPixelStick interface. I have also mapped the element to all 1320 outputs of the ESPixelStick (E1.31) controller in Vixen. I try to send anything from vixen and nothing happens. I have all my ESPixelSticks and Vixen set to Unicast and have static IPs setup for everything, and all my other elements work fine but I cannot get this darn sign/matrix/grid to work.

I have read where ESPixelStick will roll over to the next universes if you have more than 170 pixels listed in the interface. I am at a loss here and could use some Vixen setup help using more than 170 pixels off a single ESPixelStick.

Can you post a screenshot of your Vixen 3 output configuration for the controller, and ESPixelStick main status page, and Device Configuration page? Also is your Vixen machine hardwired?


Reply
Posts: 23
(@twukken)
Eminent Member
Joined: 9 years ago

Will you be offering any more of these? Looks like Amazon sold out.
Trying to get a early start for next year

Thanks


Reply
Posts: 231
(@mwestling)
Reputable Member
Joined: 14 years ago
sporadic wrote:Can you post a screenshot of your Vixen 3 output configuration for the controller, and ESPixelStick main status page, and Device Configuration page? Also is your Vixen machine hardwired?

sporadic, thank you for the reply. Sorry I am late replying to this, but I did manage to finger it out. Here is how I setup Vixen so it worked:
Created an E1.31 controller with a total of 1350 outputs (9 rows of 50 pixels = 450 pixels * 3 channels for R G B = 1,350 channels). I then configured the controller with three universes.
1 - Start 1, Universe 208, size 510
2 - Start 511, Universe 209, size 510
3 - Start 1021, Universe 210, size 510 (Knowing that anything past 1,350 will be ignored)

Unfortunately I have already torn down the show so I cannot get a screen shot of the ESPixelStick configuration, but if I remember correctly I had the ESPixelstick set to a starting universe of 208 and a pixel count of 450.

The show laptop was hardwired to the router, then wireless from there. That seemed to keep any potential lag down to a minimum.

I don't remember what exactly it was that I did beyond my initial setup in my post and this post to fix it. It is all a blur about now, but I remember that at some point I had an IP conflict with one of the Komby's and that may have been the source of my angst. Note to Self: ALWAYS keep your IP Addressing map up to date!!!

BTW, this is my first year running your ESPixelSticks as I ran Komby's last year and what a fantastic difference. (Not meant as a knock to Komby as those units are awesome and are still used for some other elements and functions) Less number of reboots needed, faster processing of sequence commands, much simpler configuration (when you do it right!) and much larger range of number of pixels supported. Thank you very much.

Oh and I am also seconding the request for another group buy. I am planning on going with more pixels next year and will need at least 10 or more of these!!!


Reply
Posts: 19
(@cengiz)
Active Member
Joined: 11 years ago

Hello,
Apart from the espixelsitick V3 flash tool, I want to install it with arduino ide software. I get the following errors. What am I doing wrong?

Thank you.

C:\Users\istan\Documents\Arduino\libraries\ESPAsyncUDP-master\src\AsyncUDP.cpp: In member function 'bool AsyncUDP::listenMulticast(ip_addr_t*, uint16_t, uint8_t)':

C:\Users\istan\Documents\Arduino\libraries\ESPAsyncUDP-master\src\AsyncUDP.cpp:254:57: error: 'udp_set_multicast_netif_addr' was not declared in this scope

udp_set_multicast_netif_addr(_pcb, multicast_if_addr);

^

C:\Users\istan\Documents\Arduino\libraries\ESPAsyncUDP-master\src\AsyncUDP.cpp:258:36: error: 'udp_set_multicast_ttl' was not declared in this scope

udp_set_multicast_ttl(_pcb, ttl);

^

exit status 1
Error compiling for board Generic ESP8266 Module.


Reply
Page 84 / 95
Share: