ESPixelStick - E1.3...
 
Notifications
Clear all

ESPixelStick - E1.31 WiFi Pixel Controller

948 Posts
178 Users
0 Reactions
503.7 K Views
sporadic
Posts: 1199
Topic starter
(@sporadic)
Noble Member
Joined: 14 years ago
pixelpuppy wrote:Does this new release include the testing function mentioned below?

It does.

MartinMueller2003 wrote:For me, I have found the original RenESP hardware very useful as a general ESP-01 programming platform. Having the ability to just plug the usb-to-serial device directly onto the board is very useful. That and having the PB that can be used to put it into programming mode (jumper is no fun). If it could run two strings that would be helpful. I never power my strings from the ESP (so fuses are a bit of a don't care for me), I always power the ESP from my stings so preserving that would be good.

Ease of programming is definitely something I want to do. Adding on-board USB programming is a little over-kill for the design I'm thinking about, however I've considered designing programmer that can toggle the module into programming mode so that the user never has to mess with the buttons to trigger flash mode. Similar to how a NodeMCU works. Could still be programmed the way it is now if someone didn't have the programmer. This of course wouldn't work with ESPixelStick as the reset line isn't on the programming header.


Reply
Wildbill
Posts: 259
(@wildbill)
Reputable Member
Joined: 16 years ago

2 outputs would be nice [emoji106]
More than that is overkill for what it is intended

Sent from my iPhone using Tapatalk


Reply
kwoodard
Posts: 281
(@kwoodard)
Reputable Member
Joined: 13 years ago

Will this upcoming beta software version also include support for multiple universes when running multicast? I just read that feature was in the 2.1-dev version, but I hadn't updated to that version. My plan was to update to the 2.1-dev version next weekend, but now I'll use this new beta version.

I definitely like the idea of additional outputs. A low-cost, wifi-based 2 or even 4 channel board seems to make a lot of sense. I think the ESPixelStick was a game changer. You could get into pixels with a $10 controller and drive small props (I even drive 8' 180 deg trees with them).


Reply
sporadic
Posts: 1199
Topic starter
(@sporadic)
Noble Member
Joined: 14 years ago
kwoodard wrote:Will this upcoming beta software version also include support for multiple universes when running multicast? I just read that feature was in the 2.1-dev version, but I hadn't updated to that version. My plan was to update to the 2.1-dev version next weekend, but now I'll use this new beta version.

Yep, it will. You can still flash via the OTA update file which I'll provide as well.

I definitely like the idea of additional outputs. A low-cost, wifi-based 2 or even 4 channel board seems to make a lot of sense. I think the ESPixelStick was a game changer. You could get into pixels with a $10 controller and drive small props (I even drive 8' 180 deg trees with them).

Thanks! Two to four output is what I'm thinking.


Reply
Posts: 93
(@kockie)
Trusted Member
Joined: 11 years ago

I'd like to see a version that can drive one or more powerleds *(10-20-50-100W) with a rgb led-driver


Reply
Posts: 672
(@pixelpuppy)
Honorable Member
Joined: 12 years ago
kockie wrote:I'd like to see a version that can drive one or more powerleds *(10-20-50-100W) with a rgb led-driver

Are you talking about something like this?
http://doityourselfchristmas.com/forums/showthread.php?46177-PixiFlood-Flood-Driver-with-ESP8266/page6&highlight=esp+flood


Reply
aknflyer
Posts: 371
(@aknflyer)
Reputable Member
Joined: 10 years ago

Would be nice if it had a sd card for sequences, and could work with the falcon sync pulse, eliminating the streamed data over the wireless. Just a thought.


Reply
Posts: 57
(@aclarksr)
Trusted Member
Joined: 13 years ago

Can I use my PICkit 3 or do I need to get the CP2102? Never mind, for $2.50 what does it hurt?

Sent from my iPhone using Tapatalk


Reply
Posts: 93
(@kockie)
Trusted Member
Joined: 11 years ago

Yes, something like that. I'm afraid it will be too late for the application I need if for... I could use one or a couple in early August (in the Netherlands).

The ws2811 pixeldriver that ROBG made would also be ok to me, but I was too late 🙁


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

AT Request for sd card. The ESP-01 has limited IO pins. We might have to move to one of the devices with more IO (they come with more rom memory and drive the price up 3-4 dollars) to support such a request.


Reply
Page 56 / 95
Share: