Ok. I am at a loss here. Everything checks out and I have replaced the last pixel upstream from this prop. If I go full white the first 10 pixels work fine and the rest flicker erratically. If i change to any other solid color they all work fine. I did notice a very slight flicker on the last couple pixels when doing all blue. The next two props downstream are both working fine. Here is the kicker....if i move this one ahead of the upstream prop it works fine. Any ideas? Thanks!
all white:
all red:
Sent from my SAMSUNG-SM-G900A using Tapatalk
This might apply to you. Mine was Data signal issues. I had problems over 30 feet with my pixabulbs. Try running some cat5. Use one twisted pair for data and ground. Then use others for power and ground. I found that my insulated 18/4 speaker wire could not handle over long distances.
I still use the speaker wire under 30 feet. Over 30 feet no go.
My distance is not that great. About 6 feet from the last prop and the next prop down the line is still working fine so I don't think I am losing data...however, if I turn this one full white so it is flickering then try and turn on the next one full white is continues the flickering pattern....and I just swapped another prop into this ones position in line and it works fine so this one must the culprit....can't figure this out since it works fine when it is moved earlier in the line....is it possible different pixels have different sensitivity to varying data conditions?
OK. I just swapped this prop (we'll call it #4 for its position in line) with #2. It works fine in the #2 slot and now the one that was #2 is giving a similar flicker when in the #4 slot. The #5 prop does not flicker unless #4 is already on white. Since I was just trying to test each individual prop at this point I have not hooked up power injection.....could that have anything to do with it? Not trying to run all props at once....yet. 🙂
Oh and yes. All my props have power injection at end of strings. So my issue was Data issues. Increasing power voltage will mask data issues.
Well I fixed all the identifiable issues and still have the flicker but I am now pretty sure it must be power...I can now get all 6 props running red with minimal flicker so I will assume data is flowing all the way (as well as power) and will finish the connections to add injection. Check out the big red HOs!
:biggrin:
Oh...and this is 250 pixels running one PX1 for those who might be looking to exceed the 200 limit...it does work!
First, check te connectors. I've had flakey behavior when a connector was bad. If you question power...go all white and see what your voltage is at the end. Also, people have had problems when using a pair to send data for pixels. It was documented in ACL.
Sent from my LG-H811 using Tapatalk
Scott - Were you going USB->RS485 to the PX-1? I've been struggling with similar erratic issues that seem to have been resolved by running E1.31 and controlling the PX-1 from a bridge. Like to know what your set up was and how your resolved.
jsheehan3 wrote:Scott - Were you going USB->RS485 to the PX-1? I've been struggling with similar erratic issues that seem to have been resolved by running E1.31 and controlling the PX-1 from a bridge. Like to know what your set up was and how your resolved.
My setup is simple. PX1's from show PC on serial. The erratic ones were on the second PX1 in the line so it was 485 but 232 from the PC to the first one. In my case power seems have been the culprit. I finally finished the injection lines and it all seems to be OK now. Still have some setup issues in Vixen but that is for another post. 🙂
I should probably rename this thread to "what next?" so here goes. I found and fixed all the solder, strip, connection and power issues. All 6 letters (HOHOHO) seem to be working fine. I remapped some of the color handling so they all show the same color at the same time. I thought all was good.... Using the web interface I am able to light any or all of this at will. Any pixel, any color and it all works. BUT....when I try to run a sequence to really test it things go wonky again. Now, when I run a sequence as soon as an effect starts, all the pixels come on. The first HO goes all blue and then the second and third ones go all green. Whatever effect I use just runs over the top of the color. When the effect ends, they all go off. What the heck???
Any ideas? :hmm:
