Notifications
Clear all

E682 Capability

14 Posts
8 Users
0 Reactions
4,447 Views
Posts: 1115
Topic starter
(@11bravo)
Noble Member
Joined: 14 years ago

Another thing I need to concentrate on is what I'm going to use to attach the pixel strings on for making the 180deg tree.


Reply
Electrified3
Posts: 716
(@electrified3)
Prominent Member
Joined: 13 years ago

They do sell pre-fab hook heads, not sure what you are using though for the center? A pipe? Not sure if there is a ready made hook head for a 180 deg tree with 16 strings though, others might be able to speak up on that.

What I use for the heads on mine is a pipe coupling that I drill and tap out around the center for 1/4"-20 bolts, then I install eye bolts into them and use that as my upper support. If you had a 3" or 4" pipe coupling, drill out 16 even spaced holes for 1/4"-20 bolts on 1/2 of the coupling, put some long eye bolts in there, then use reducers to get the coupling down to the size of your center pipe that might work. I run electric fence wire from my bottom ring to my eye bolts then back down, doing all of my connections on the ground. I tie the lights to the electric fence wire to support them so they are not supported from the pixel wires.

Take a look at the 3 or 4 wire connectors from DIYLEDEXPRESS, they work pretty well for things like this and they sell "T" fittings and prefab extensions. If you double them up, so 100 lights per output then just tie the +/- leads from the start and end of the string together and the data on the incoming side you can easily wire all 16 strings to 8 outputs and should take care of any power injection issues. Update rates are still good, worst case for load is 6 amps for 100 pixels (Odds are you will never hit anywhere near that long enough to blow the 5 amp fuse on the E682). You end up with 8 cables out of your controller to your tree and have 8 more outputs to use for your star or anything else you might want to add in later.

If interested in something like that I will try to dig out one of my coupling heads and get some pictures for you.


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

I have a pre-made 16-hook hookhead for my mega tree - I have 30 strands so I put 28 doubled up and then singles on the end (15 on each side to match my controller inputs). Mine is set up for 240 degrees but could easily be used for 180 degree - you won't notice the unused hooks in the back at all. One thing though, you may want to run a couple cables from the back anyway to help balance out the pull from the front of the tree. You might end up with it bowed towards the front. I tie mine down to the ground with small bungee cords to keep the pull constant - I learned to do a few on each side at a time or the thing would be lopsided...


Reply
Posts: 1115
Topic starter
(@11bravo)
Noble Member
Joined: 14 years ago
Electrified3 wrote:They do sell pre-fab hook heads, not sure what you are using though for the center? A pipe? Not sure if there is a ready made hook head for a 180 deg tree with 16 strings though, others might be able to speak up on that.

What I use for the heads on mine is a pipe coupling that I drill and tap out around the center for 1/4"-20 bolts, then I install eye bolts into them and use that as my upper support. If you had a 3" or 4" pipe coupling, drill out 16 even spaced holes for 1/4"-20 bolts on 1/2 of the coupling, put some long eye bolts in there, then use reducers to get the coupling down to the size of your center pipe that might work. I run electric fence wire from my bottom ring to my eye bolts then back down, doing all of my connections on the ground. I tie the lights to the electric fence wire to support them so they are not supported from the pixel wires.

Take a look at the 3 or 4 wire connectors from DIYLEDEXPRESS, they work pretty well for things like this and they sell "T" fittings and prefab extensions. If you double them up, so 100 lights per output then just tie the +/- leads from the start and end of the string together and the data on the incoming side you can easily wire all 16 strings to 8 outputs and should take care of any power injection issues. Update rates are still good, worst case for load is 6 amps for 100 pixels (Odds are you will never hit anywhere near that long enough to blow the 5 amp fuse on the E682). You end up with 8 cables out of your controller to your tree and have 8 more outputs to use for your star or anything else you might want to add in later.

If interested in something like that I will try to dig out one of my coupling heads and get some pictures for you.

I really haven't got the plan finalized yet, because I don't know what all I need. I've done some searching on others designs. But haven't decided on what type of support to use.

The electric fence wire that you support the pixels strings with, that worked for you ok, and held the pixels straight? You didn't say what type of Pixel your are using.

Do you think 16 strings is too spread out in a 180 pattern? If so maybe I should tighten it up a little or add more strings, and double them up like you say.

I'm definatly interested in any photos of how you did it.

I have a welding machine, and a mig welder. Lots of tools and a big shop. I can usually make most anything.


Reply
Page 2 / 2
Share: