Will one E682 control 16 WS2811 Strings? 50 pixels per string? 16 strings is what I have planned for the pixel mega tree.
Reason I am asking this question is I've done got myself confused from all the reading I've done.
And I don't understand the output configuration section of the E682.
A snipit of that page in the link: I don't know if what I have is right or not.
http://doityourselfchristmas.com/forums/album.php?albumid=332
The configuration screen looks correct. You might need two power supplies but I don't see why it wouldn't work as configured.
Thank you for the reply, I have extra 5v 60amp pwr supplies.
The worst case condition would be 16 strings x 50 pixels x .06A/pixel = 48A so a single 60A supply would work OK - if you have an extra supply not doing anything, then it wouldn't hurt to double them up and run each half from one supply.
If all you will ever run off of this controller is just that tree your set up looks good. Nice part with how you have it laid out is no need for any power injection since strings are all just 50 pixels long. 1 power supply should be just fine at 300 Watt.
You do have a lot of capacity left in the controller though, if running unicast you can have the potential to run another 1240 pixels more off of it. If you planned on using that capacity in the future I might look at changing them up to 100 pixels long (2 strings per output) then use groups 1 and 2 only for the tree, then later down the road you can add other things to groups 3 and 4. If you tied the strings together at the top and on the bottom tied the +/- together and only send data into the start of the first string you can cut your wiring from your controller in 1/2 and leave the extra capacity available from your controller to add on in the future without having to re-wire things.
Your way will work just fine though, is neat and clean, properly fused and so forth, pretty simple to work with.
Love the new avatar Electrified....
Reminds me of Castle Wolfenstein.
:devilred:
I ran this configuration last year:
2xE682
32x WS2811(33 count)
2x 12vdc PSU, one PSU per unit
I tested the setup with 32x WS2811(50 count) before cutting each string back to
Zero issues
Aurbo99 wrote:I ran this configuration last year:2xE682
32x WS2811(33 count)
2x 12vdc PSU, one PSU per unitI tested the setup with 32x WS2811(50 count) before cutting each string back to
Zero issues
wow 32 string mega tree?? mine is only 24 and i though it was full lol .... 16 ft tall tree?? what is the base ?? 12 ft ?? i am planning another one and i am not sure how big to make it yet .... as for 11bravo set up ..using 16 plug from the 682 will not leave any room/plug for the star !!! on my set up i save the last bank for my star ...but like other said ..you still have plenty of room/ power on the 682 ..so maybe you migh what to go up and down using 100 pixel to get the room for the star ...if you did not purchase your pixel you migh whant to go 12 volt with 100 pixel so u can go up and down and have extra for arch or star like i did ..cheer
The biggest I know is Aaron troxel who had a 64 string megatree, all were ws2811 flex strips 12v. He also had 16 arches , each 2 strips of ws2811's . Cars drove through the arches. He had a 3rd element of 32x120 tm1809 flex strips mounted in lexar plastic and mounted over the entrance to the city park. The entire show ran from two pi players. He used falcon-16 controllers to drive the lights. He started in sept and had a show opening thanksgiving. Something like 6 weeks. 128 strips of lights mounted and sequenced in six weeks. It helped that he did this for the city park and the city offered city workers to help. For example they planted a telephone pole in the park to hang the 64 emt pipes to for the megatree. I wish I had his labor pool. Still, pretty amazing
Electrified3 wrote:If all you will ever run off of this controller is just that tree your set up looks good. Nice part with how you have it laid out is no need for any power injection since strings are all just 50 pixels long. 1 power supply should be just fine at 300 Watt.You do have a lot of capacity left in the controller though, if running unicast you can have the potential to run another 1240 pixels more off of it. If you planned on using that capacity in the future I might look at changing them up to 100 pixels long (2 strings per output) then use groups 1 and 2 only for the tree, then later down the road you can add other things to groups 3 and 4. If you tied the strings together at the top and on the bottom tied the +/- together and only send data into the start of the first string you can cut your wiring from your controller in 1/2 and leave the extra capacity available from your controller to add on in the future without having to re-wire things.
Your way will work just fine though, is neat and clean, properly fused and so forth, pretty simple to work with.
You know I completely forgot about the Pixel Star.
I purchased a E6804 also. I intended to use it for arches, but decided not to do pixel arches this year. I suppose I could run the star with the E6804.
I have plenty of power. I also purchased four, 5v 60amp power supplies.
And I already purchased the 5volt pixel strings too. So I got to go with with I have bought.

